Models > YKERI204PB1

YKERI204PB1 KitchenAid Range - Overview

Get Parts and Repair Help for YKERI204PB1

If you know the range repair part you need, you can browse the list of all parts on the YKERI204PB1, or you can search by name or part description. You can also find your part by where it is located on the YKERI204PB1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for YKERI204PB1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

$22.47

Standard Y-Frame Surface Burner - 6" - 1500W

The manufacturer suggests replacing the receptacle at the same time.

$18.27

Receptacle Kit

This surface burner receptacle assembly comes with the receptacle, two wires, two wire nuts, and two pieces of heat-shrink tubing.

$2.70

Screw

This screw is sold individually.

$37.32

Surface Burner Element Switch - 8"

This control switch controls the stove top 8" surface burner.

$41.06

Oven Rack

Sold individually.

$49.07

Surface Element - 8" - 2100W

This element has looped terminal ends and 5-turns.

$67.62

Sensor

This temperature sensor detects the temperature within the oven cavity.

$7.18

Drip Bowl - 6" - Black

Sold individually.

$2.70

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure an electrical connection is not lost.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the element did not turn compleatly off, the on light stayed on.

  • Customer: chaz from fairplay CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 38 of 42 people found this instruction helpful
removed the screws holding the back metal panel, this exposed the wires to the switch. tested the wires to find that they were live when the switch was in the off position. ordered a new switch. UNPLUGED THE STOVE. removed the knob on the front of the stove. this exposed 2 screws, removed screws and the switch came away from the stove. removed each wire fro... read more

temperature not accurate after 3 1/2 years of happy usage

  • Customer: Ruth from Oregon IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 60 of 115 people found this instruction helpful
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I tur... read more

Replace shattered outer door glass

  • Customer: Philip from Vandalia MI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 29 of 36 people found this instruction helpful
This is not the best design. You'll need to have an extra set of hands to hold the trim pieces in place. Remember the glass is positioned outside [on top of]the trim pieces. Be careful as the trim pieces are rather brittle and can be hard to locate in their proper position. Position glass in the holding tabs at the bottom, hold glass against the trim piece... read more