YKEHC309JW2 KitchenAid Microwave Oven Combo - Instructions

Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!

This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

Removed the oven door by following the straightforward instructions in the user's manual. Removed philips head screws to take the door assembly apart. Removed clips holding the two inner door glass plates, and the two plates. Removed the clamp holding the broken glass plate, then the glass and associated glass fragments. Then cleaned and re-installed the three glass plates and their clamps in reverse order. Re-assembled the door and re-attached to the oven. Only cautionary note is to be careful when removing, handling and re-installing the various glass plates. Watch out for fragments from the broken plate; they can cut you and/or fall on the floor.

Important note: hinges are left and right do not mix them up or door will not re-assemble properly and you'll get to do it twice.

Steps I took:

Removed the oven door per the instructions in the oven operator manual. Removed several screws to release the interior steel liner.

Removing the steel liner was a bit of a hassle, Had to manipulate it to get it loose but it eventually came away from the stainless steel exterior door panel.

Disassembled the interior glass layers, there are three. The glass you need to replace is the last layer, of course. removed and discarded the broken glass. Note: the interior glass is not secured by a bracket or screws, it is held in place by compression of the interior steel liner and a another liner that is inside the door assembly (you'll figure this out when you dis-assemble).

Another note: there is a fluffy material gasket between these two liners, use care when you disassemble or the fluffy gasket will turn into confetti.

Take the opportunity to clean all glass and parts of the accumulated oven grease.

Re-assembled door and re-installed...looks good.

Another note, getting the door back together requires a little patience because there are clamping overlaps of the steel liner to the SS exterior door panel. Be prepared to jockey things around a little and make sure all your screw holes are all lined up before you begin to button it up. Remember, hinges are left and right they are not interchangeable.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

After popping the last few kernals of popcorn, we hear a different kind of pop sound come from our microwave oven. When we looking inside, we found that the glass turntable had broken unevenly in half. Although we didn't understand why it had happned, we did know we'd be without the use of the microwave without a new one. After less than 10 minutes surfing online, I had found the correct part on PartSelect.com and had arranged to have it shipped to me by speedy delivery. Once it arrived, I just popped the new turntable into the microwave and used the box to dispose of the broken one. It could not have been easier and it saved me the cost of a service call and likely further delay.

Unfortunately, you must replace the whole door. It was only a matter of removing 6 screws but sliding the door back on was a little tricky. Still, it beat calling a repair man and the item came in 3 business days. The part fit exactly right.

Safety first , I shut off the circuit breaker . I removed the racks from inside the wall oven . I removed the the wall oven from the niche .Then removed the three sheet metal panels in the rear of the oven exposing the mounting screws that hold the blower down .I removed the wires from the blower motor and then the blower assembly ,then I removed the small duct affixed to the blower assembly by a single sheet metal screw and transferred it to the new blower assembly . I installed the adhesive backed foam strip that is a vibration dampener and reassembled in reverse order.Once the over was returned to its original position in the wall mounting I turned the breakers back on and tested the oven ...AAAAAAAAA++++++++++++ To be fair i must admit that I am not a novice at this 15 years of my working career revolved around HVAC and appliance repair ,still however a novice that is mechanically inclined can perform the same task in about 70 to 80 minutes as opposed to my 35 . That is all there is to it.

There are two lights in this model oven. The glass will open by pulling outward on the near end. Since these are halogen bulbs I used a clean cloth to hold the bulb while replacing. Bulbs are expensive especially when purchased from Kitchen Aid dealer. I got two bulbs from PartsSelect delivered in two days for considerably less.

Removed a screw and clip to remove the lens and replaced bulb. Then replaced clip and screw. Done.

First, I removed the grill from the top of the microwave by removing 3 screws and then by sliding it out. It was a bit tricky, but you have to rotate it under so the grill comes out from behind the display.
Next, I removed the bottom grill by removing 4 screws. This one removed easily. Then, I removed 2 more screws that were under the bottom grill and was able to start sliding out the microwave unit.
I was only able to pull the microwave half way out because some wires were stopping me from pulling it out more. I removed the big square piece of insulation and had enough room to get to the light assembly.
I removed the retaining clips by pushing the right side of the clips to the little opening in the middle on the right hand side. Then I was able to remove the light bulb and replace with the new one.

Easy, pulled out the old dis-colored racks and slid the new ones in. I was VERY happy with the quick receipt of my order. If I ever need parts again,this is where I will go

Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

The repair is straight forward. The only complication anyone seems to be having is removing the door ( which is a definate must to do this repair properly). So I would like to add some details about removing the door. The manuel shows the allen wrenches going into what looks like the hinge itself to release it from the oven. This is not the case. The holes that the 5/32 allen wrenches go into are actually behind the hinge itself. I wrapped the allen wrenches with some painter tape to protect the surface of the door and oven from scratching. Then, simply insert the short end of the allen wrenches, one on each side, into the holes behind the hinge. Then as it shows in the manuel, gently close the door. But not all the way. As you get about 80% closed you'll feel resistence. That is the time to grasp the bottom of the door and start to lift it from the bottom, while stablizing it with the other hand holding the handle on the door. The hinge will start to release from the oven as you continue to press it closer to being all the way closed. The hinges will release if you are doing this correctly before the door can be all the way closed.

Hope that helps. Otherwise, once the door is off. Unscrew all the screws...pay special attention to what you are unscrewing and how it all fits together, because you're going to have to put it all back together again. Some of the glass is held in place with clips and some of it is not. Just lay it down flat and be careful to not force anything in or out and you'll find it quite easy.