YKEBC208KS0 KitchenAid Wall Oven - Instructions

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

I follow the directions on the Maytag site. It is a very simple job. I appreciate the Information I got from Becky when ordering the hinges.

Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.

It most likely would have gone quickly had we ordered the right part!

It went fine once you imbeciles sent the right part, thank you for miss labeling it on the website and costing me time, a week without an oven, and extra expenses. The inner GLASS is the inner GLASS, not the middle glass of a layered three glass door!

First I removed the door from the double oven as instructed in the owner's manual. Then I removed the screws holding the door together. I removed the layers necessary to get to the inner door glass. Then reassemled it in the order that I had taken it apart. A total of 15 screws. My tip would be pay close attention to how you disassemble.
Not only did we save the cost of a repairman but because of Part Select we got the glass for less than half the price quoted to us from Kitchen Aid for the part and delivery.
Very satisfied with our experience with Parts Select

removed door, took out 8-9 screws, slid door upward, and removed. took out broken glass, and replaced.

fairly easy. took a while to reassemble. otherwise all was ok.

unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced

I did not take the door off the oven, i dissassbled it in place. all the visible screws on the door have to be removed. The "vent" air diflector or what ever it is , between the upper and lower doors has to come off also to access the screws that hold the front of the door on. The only confussion i had was the bracket that holds the third layer of glass. I forgot that it is held on with the same bracket/screws that hold the secound layer on.

I found some of the feedback posted on this site very helpful. Taking photos as I went along was also very helpful in remembering how to put it back together. There are several over-lapping pieces to the door and you have to be careful to put things back together in the correct order. Lining up the screw holes on the hinges with the door is also a little tricky.

Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan