This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
This inner door glass is used in ranges. It creates a transparent heat barrier inside your oven door. For this installment, the only tool needed is a #2 Phillips screwdriver. To repair, first remove t...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
This bottle of non-abrasive cooktop cleaner breaks down and gets rid of the hardest baked-on stains and residue without causing any harm to your appliance. The bottle is 10 oz and does not require a l...
The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the ...
The light cover lens in your oven is designed to protect the light bulb. If your light cover lens is damaged, you will need to replace it. This part is made of clear glass and is roughly 3 inches in d...
I removed the oven door by lifting it off with the hinges. Disassembled the door parts one at time making sure I remember where I removed the screws until I am able to get to the broken glass. The most difficult part is making sure that the insulation strip & the gasket stayed in place after I replaced the broken glass & doing the reverse
... Read more process of installing the parts together. Relatively easy process as long as you remember where the parts go. When in doubt, I had to refer to the pictorial of the disassembled door shown on your website.
I removed bottom drawer of the kitchen aid oven.I could see the gas valve.I opened the door of the oven and removed plate on bottom of the oven .there was no screws holding it down ,I removed a couple of screw for the burner and took out 2 screws for the heating element . In the back of the oven .there is 2 wi
... Read moreres .one goes to the gas valve located behind the bottom draw.you know can see it from the front with the draw removed,than move the oven out and take the 4 screws holding the back plate .you will see the other wire the element plugs into .you unplug 2 wires and a few screws and you are done.you save alot of money and since this happens alot .you can compare this to changinging a light bulb.It needs maintence from time to time.
First, layed tape across all broken glass to keep glass from shattering more and releasing more bits of glass. Pull up and out the oven door. Had table set aside covered with an old sheet to lay door on, After laying door on table, Removed outer screws. Needed phillips #2 & #3 tip widths and electric screwdriver, for inner screws that whe
... Read morere difficult to remove. Making notes of what came off first! ( (rt & left, bottom,/top) when removing metal frame braces, and in what order they go in when reassembled . Did the same with screws & set them aside in groups. Then marked the groups of screws. Removed the metal door panel. Carefully removed the in between panel of glass. Set Outer glass aside along with metal "door"and inner door glass,and proped them up in a safe place. Carefully removed the broken & shattered inside glass wearing rubber gloves. Had a garbage can next to the table to with news paper to wrap glass. Cleaned area. Replaced glass taking care not to tighted screws so much as to break the glass. Put added insulation.(Whcih was not the same as in diagram), around the edge. put back the inner glass panel, care not to leave prints, tighten screw ( care not to break glass) Cleaned the door sides and bottom, all had alot of grease buildup. Put back the metal door portion. Cleaned the outer glass door front and back. Being careful not to break it (or leave prints inside). Replaced the side and bottom metal frames. Wiped it down and put door back on stove.