YGSC308PJB2 Whirlpool Microwave Oven Combo - Instructions

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

Have a Whirlpool Accubake self cleaning wall oven that quit working after doing a cleaning. Found that the thermal overload safety thermostat might be the problem. Ordered the part which arrived in a couple of days. Installation was very easy and took about 10 minutes. First turn off power to the oven. Slide the oven out, remove the back panel, remove the old safety thermostat which has two wires coming off of it, and replace it with the new one. Put the back panel on and slid the oven back in. Turned the power to the oven back on and we had heat. Problem solved.

Went to PartSelect on the internet and looked up my model. Next I selected the problem from a short list of questions, which indicated the broil element was the problem 99% of the time. With this bit of confidence I ordered the part which was delivered in 2 days. The first step in the repair was to turn off the circuit breaker for the oven. After removing four screws that held the broil element in the oven, I pulled the electrical connectors apart on each end of the old element and attached the new unit to the electrical leads. Lastly I pushed all the wiring back inside the back wall of the oven and replaced the four mounting screws. I then performed ops check, which worked. End of story, job done in about 10 to 15 minutes. Easy Peasy.

I did some research on blogs and identified the thermal fuse as likely culprit. Ordered part from PartSelect.com, but had to call the 800 number because the parts diagram doesn't show this fuse, just the thermostat. The fuse is located on the back of the oven, so it must be removed from the cabinet, but that wasn't a huge project. There are a bunch of sheet metal screws holding the top and back covers that must be removed. The fuse is held on by two screws and has two wire connections. Getting the stove out and disassembling is the hard part, but not really difficult if you take your time. I used a foot stool that was about the same height as the bottom of the oven and just slid the oven out on a piece of cardboard. Make sure you turn the power off before starting.

screwed in the new oven light

Had to screw off old terminal block & screw on new one

I removed the oven door using the instructions in the book that came with the oven useing 2 allen wrenches as described. I called up the parts list for the oven door on my computer and made a copy.This was very helpful in removeing the door and getting to the broken glass and installing the new glass The one thing that that i regret was not ordering the insulation frame that went around the new glass. It was difficult getting it back in place.I would order this part if I have to do this again. I ordered the new glass on a Saturday and the new glass was delivered on Tuesday.Thank you for the great service. Bill- Texas

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

INNER GLASS - A YouTube video on removing Whirlpool Oven Doors was very helpful. Cleaning the other two panels of glass with a Baking Soda paste worked like a dream. Re-assembly was fairly easy. The hardest part was re-aligning the outer glass cover's top holes so I could drive the screws in. LIGHT BULBS - To easy to describe.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

replace thermal safety switch on back of oven

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.