Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YGEW9877JQ1

YGEW9877JQ1 Whirlpool Dryer - Overview

Get Parts and Repair Help for YGEW9877JQ1

If you know the dryer repair part you need, you can browse the list of all parts on the YGEW9877JQ1, or you can search by name or part description. You can also find your part by where it is located on the YGEW9877JQ1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YGEW9877JQ1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the YGEW9877JQ1

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

$14.81

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not starting, will not shut off or the door will not close properly. All you will need is a putty knife and a Phillips screwdriver. Pry open the top of the dryer, remove the two screws underneath the lint collector without removing the entire thing, unplug the switch, remove the screws that hold the switch place, take out the old switch and install the new one by screwing it back into place.

$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer do...

$36.59

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one high-limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires. If your dryer is not starting properly, shutting off too soon or is taking too long to dry your clothes it could be because it has blown and needs to be replaced. This is a genuine OEM part that comes directly from the manufacturer.

$44.55

Maintenance Kit

This maintenance kit or dry repair kit is used for dryers. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. If your dryer is ma...

$12.47

Rear Drum Support Roller Kit

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining washer). The kit does not include a belt or idler pulley and rollers are not sold individually. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. The tools needed to complete this repair are a putty knife, Phillips screw driver, and a 5/16 nut driver. It is recommended to look at the rear felt before reassembling the dryer to ensure there are no gaps or damage. This is an OEM part sourced directly from the manufacturer.

$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not s...

$21.40

Thermostat, Internal-Bias

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

$5.75

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found b...

$31.06

Lint Filter

This dryer lint screen comes with a handle. This filter collects lint as it passes through the dryer vent.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door switch was bad

  • Customer: pat from lisbon,, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 891 of 913 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more

Dryer tub belt broke

  • Customer: Ray from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 821 of 873 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more

No Heat

  • Customer: Vernon from Niceville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 802 of 849 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more