YGEW9250PW0 Whirlpool Dryer - Instructions

Removed power cord. Removed screws in back cover. Checked electrical diagram. Found fuse, checked. New part arrived promptly on time. Was correct part. Tested before instalation. removed one screw that held fuse. unpluged the two wires. Repluged wires, reinstalled screw.on new fuse, replaced back cover and screws. recoupled power, tested. ran perfect.

I removed the back of the dryer (after unplugging and shutting off the gas valve) I vacuumed any fuzz and debris. I also removed the dryer vent and cleaned that too. I unscrewed the thermal fuse and replaced it with the new one. I wiped everything down and replaced the back and ran the dryer and it worked! Thanks for your help and for saving me money! My husband was so glad we didn't have to call a service man we celebrated by going out to dinner!

parts were for a dryer that would not tumble or heat they did not fix problem have called in pro hope he can fix

Took out the old one and put in the new one.

I thought that I was going to have to buy a new dryer or rather a used one to replace my dryer when it stopped heating. I knew I could not afford an appliance repair person to come out to the house, so I searched for my appliance on the internet for repair parts. Your website helped me to figure out the part that I needed to replace; i.e. the thermal fuse for $9. Since you advertised that you took return parts, I placed my order. Without any hassle short of the obvious moving the dryer away from the wall and removing the back panel I was able to do this in a short time. I was so excited to realize that my dryer was heating up. Thank you.

I removed the back panel from back of dryer, unplugged the thermal fuse as shown in YouTube instructional video. Put back panel back on, plugged in dryer. Started workimf right away. Could not have been easier! The whole process from troubleshooting the problem to oderimg and installing the part was surprisingly easy. Thanks so much! Best service I have gotten in  a long time.

I assumed a fuse was bad, although there were 3 possible fuses that might have caused the problem. I tested the Thermal Fuse #PS345113 and it was shot...the others were ok. I ordered a new fuse and everything works fine. The timer was not working on only the heated cycles but the new fuse fixed that as well. This took a bit longer than it should have because it included a lot of cleanup and moving an adjacent washing machine as well.

following the repair video made it super easy. thanks!

Watching videos on the internet, I learned how to test the parts of the dryer. I learned that the thermal fuse was the problem. I ordered the part and it arrived in a few days. I changed out the part, put the dryer back together, and it worked! Saved me a great deal of money!

replaced thermal fuse but the same result running to hot then it will not start after. had decided to reorder thermal fuse, high limit thermostat cycle thermostat. still awaiting parts as of now.

My dryer is a KitchenAid KEYE660W (electric). I tried to start the dryer but it would not run. I did notice that if I held the start button down, I could feel light vibrations through the button. Searched through Yahoo and this site and determined that this is often a bad Thermal Fuse. Used the diagrams on this site to locate where it should be, removed the back of the dryer with a screwdriver, removed the two wires clipped to the Thermal Fuse and unscrewed the Thermal Fuse. I had a friend test the fuse with a Multimeter. It was bad so I ordered another one on this site and it arrived in two days. Screwed the Thermal Fuse back in and clipped the two wires back on. Started the dryer and it worked!!! Replaced the back of the dryer. This repair took 15 minutes MAX and taught me a little bit about Mulitmeters.

Replaced with parts orded worked fine for2 hours and quit heating again

followed the you tube video, came apart ok, very bad lint problem. Vacuummed out extensively. Made repairs, very straight forward. Back together ok, still noisy but not as bad. May be the fan.

I'm a 68 year old single lady who watched the video and just followed the instructions. Took the back off, tested all the parts involved with heating and the only part that didn't have any continuity was the top part of the thermal cutoff fuse. After receiving the part I removed the old one, put the new one in, put the back on and turned the dryer on. It heated right up. I also had a part that I didn't need and your return dept. made it very easy to return. I love this site. Save me a ton of money.

Found this part on your site very EZ bought it you shipped to my door got it when you said it would be here open it installed it propblem over glad i found you guys will use again Very good website Keep up the good work THANK YOU