YGEW9200LQ0 Whirlpool Dryer - Instructions

The part worked fine, but I had ordered Grey, and got blue. Looks a little funny on a Grey Washer. Didn't want to hassle with sending it back, but I would like to have the right color.

replaced the lent filter

diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.

Our dryer got so loud after running for a few minutes that you couldn't even have a conversation in the same room. After researching for possible causes, I decided to go with new drum wheels. I purchased the Dryer Repair Kit to save a little money and it gave me a new belt and tension wheel as well (since I was going to have it apart anyways). After taking everything apart and vacuuming out all the lint from inside, I noticed that the blower wheel was broken. No idea how that happens but something must have gotten in there and broke 2-3 fins and cracked the rear side. I replaced the parts that came with the kit and proceeded to put it all back together. Started it up and it was worse than before. Quickly ordered the new blower wheel and that fixed the problem. Back to a "quiet" dryer. I probably didn't need the Kit after all, but the drum wheels were a little worn and I had it apart anyway.

Took the old one out and replaced with new filter.

I didn't have to remove the entire door...I just removed the screws with the door open, used a needle nose plier to remove the plastic insert..stuck the new one in. Then I replaced the metal portion by popping it out and inserting the new one. Easy

When I got the door catch, I held it in a pair of pliers and pushed it right into place. The door would still pop open. After awhile, I realized that the door was bent, probably by a small child climbing up on it. I had to loosen some of the screws that held the door on in order to relieve the tension in the door so that it would stay closed. As long as it continues to work, I won't worry about replacing the door. It's in a rental house anyway.

I got my kit and when I opened it the exact parts were there!! I am a older woman and was a little worried that I could do it. I took the pliers and pulled the old latch catch out and 1-2-3 walah!! It was so unbelievably easy. If I can do it anyone can. Thank you for saving me hundreds of $s on a new dryer.

Called a appliance place. They said it was a serious problem with master board and it was gonna cost 425.00 dollars. NO THANKS. Ten minutes to open ten minutes to find the problem. ( which was no were near the master board). Seconds to find and order the parts on partselect.com. got it next day. 15 to 30 minutes later my dryers running like it was brand new! Love it.

It was simply a replacement filter. No work just replace in slot. Thanks for great service and for sending in one day! We were shocked that the part arrived in one day! Will use your service again!

removed bottom panel & removed old element.

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.

Replaced the thermistor, thermostat, moisture sensor and the moisture sensor wire harness and the problem did not clear up. Tested both coils on the gas valve and the ohms readings for all 3 tests were within range. The burner would light and work until it shut off for the 1st time, it would attempt to relight but the gas valve would not open. Replaced the coils with Part # PS334310, 'M' Series New Style Coil Kit and the problem was corrected.