Models > YG226LM

YG226LM Magic Chef Dryer - Overview

Get Parts and Repair Help for YG226LM

If you know the dryer repair part you need, you can browse the list of all parts on the YG226LM, or you can search by name or part description. You can also find your part by where it is located on the YG226LM by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YG226LM parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.08

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$16.53

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$19.16

High Limit Kit

This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Lim...

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$30.24

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$14.06

Lint Filter

This lint filter screen has two side guides on either side of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide.

$37.91

Rear Drum Support Roller Kit

Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer thi...

$2.70

Blower Wheel Clamp

$36.29

Blower Wheel

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

NO HEAT

  • Customer: Stan from Riverside CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 363 of 365 people found this instruction helpful
LIFT THE TOP. REMOVE (2) SCREWS HOLDING THE FRONT OF THE DRYER IN PLACE. LIFT THE FRONT OFF THE 2 RETAINING CLIPS ON THE BOTTOM OF THE DRYER. THE HARDEST PART OF THE INSTALL WAS REMOVING AND REPLACING THE IGNITER. A COUPLE OF HELPING HANDS FROM THE GIRLFRIEND TO Hold the PARTS IN PLACE WHILE I replaced the two screws was very helpfull. installing the multi r... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 161 of 182 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Electric dryer would not heat - Thermal fuses - $25 fix - I love DIY

  • Customer: Ronald from Fredericksburg VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 108 of 115 people found this instruction helpful
1. Unplug dryer from power outlet
2. Lift dryer top from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in cloth to help lift.
3. Locate heating element - rear top behind drum
4. Unplug red wires to the high limit thermal fuse
5. Unplug red wires to the heating element
6. Unlug white wires to the ... read more