Models > YG20JA4

YG20JA4 Magic Chef Dryer - Overview

Get Parts and Repair Help for YG20JA4

If you know the dryer repair part you need, you can browse the list of all parts on the YG20JA4, or you can search by name or part description. You can also find your part by where it is located on the YG20JA4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YG20JA4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$13.44

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$13.95

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.

$25.16

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$21.53

High Limit Kit

This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Limit: 258) the gas high limit (Limit: 240) and the gas and electric high limit thermostat (Limit: 300).

$15.10

Lint Filter

This lint filter screen has two side guides on either side of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide.

$12.38

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$37.91

Rear Drum Support Roller Kit

Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer thi...

$2.70

Blower Wheel Clamp

$2.70

SCREW

This screw is sold individually.

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

lint filter broke

  • Customer: Jane from Grand Forks ND
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 460 of 462 people found this instruction helpful
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday read more

NO HEAT

  • Customer: Stan from Riverside CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 367 of 371 people found this instruction helpful
LIFT THE TOP. REMOVE (2) SCREWS HOLDING THE FRONT OF THE DRYER IN PLACE. LIFT THE FRONT OFF THE 2 RETAINING CLIPS ON THE BOTTOM OF THE DRYER. THE HARDEST PART OF THE INSTALL WAS REMOVING AND REPLACING THE IGNITER. A COUPLE OF HELPING HANDS FROM THE GIRLFRIEND TO Hold the PARTS IN PLACE WHILE I replaced the two screws was very helpfull. installing the multi r... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 193 of 218 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more