Quick Question!

Have you ever purchased from PartSelect.com before?

Models > XRBR904BS

XRBR904BS (PXRBR904BS0) Amana Refrigerator - Overview

Get Parts and Repair Help for XRBR904BS

If you know the refrigerator repair part you need, you can browse the list of all parts on the XRBR904BS, or you can search by name or part description. You can also find your part by where it is located on the XRBR904BS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for XRBR904BS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$96.00

Replacement Ice Maker

This is a replacement ice maker. This assembly includes the ice mold and the control device. The water inlet valve pumps water into the mold, which stays there until it is frozen s...

$30.17

Center Crisper Rail - White

This is a center crisper rail for your refrigerator. This part acts as a support rail for the crisper drawer by holding the center of the crisper frame. You will need to replace this part is if your current drawer is not opening or closing properly. This crisper rail is white and it is made entirely of plastic. It is roughly 13.5 inches long, and 2.5 inches wide.

$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 Volt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.

$22.07

Light Switch

This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is t...

$4.87

Screw

Sold individually.

$4.89

Deli Drawer Glide - Right Side

$5.41

Glide - Left Side

$30.23

Fan Blade

Used with Evaporator Fan Motors.

$19.63

Light Switch - 2 Terminal

The light switch terminal is used in refrigerators and freezers to help you see inside your appliance by turning on when the fridge door is open and turning off when the door is closed. The measurements of this part are: 1.12 inches in length, 1 inch in width, 1.75 inches in height and 0.026 pounds in weight. If your light switch terminal is damaged or the light does not turn on when fridge door is open, replacing the light switch terminal can solve the problem. As a safety precaution, remember to unplug your fridge from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions and a detailed guide.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 739 of 786 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 256 of 331 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Cracked & Snapped Center Crisper Rail

  • Customer: Ruth from Roxbury, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 167 of 176 people found this instruction helpful
A very easy fix took all of five minutes read more