WZRE5260F0GG General Electric Washer - Instructions

I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.

Took off old agitator, removed coupling that was bad and put new one on.

I used the video instructions sent to my email and everything worked perfectly as instructed.

Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.

Couldn't get the agitator off by pulling up, then thought about it and got 2 carpenter claw hammers, inserted one on each side and puled up evenly on both and off she came. Sprayed the slots with WD Forty and popped the new on. THANKS saved us a lot of money!!!

Unplug washer, turn off water and remove the supply hose, remove 5 torex screws remove panel disconnect two wire plugs remove 2 philips screws squeeze hose clamp remove old valve install new valve reversing directions

Unplugged power cord and shut off water supply. Then removed both water hoses from the dual water inlet value using adjustable pliers. Next removed four (4) star screws on top of the control panel. This required the purchase of a #20 torq screwdriver from sears costing $3. 99 Plus tax etc. Once the top panel lifted upward and to the left I was able to unplug both electricle connections on the water inlet vlaue. Next unscrewed two phillips head screws holding the water inlet value in place. Installed the new water inlet value in reverse of above. Time to complete was 22 minutes. Very easy repair to accomplish.

We were lucky, the agitator came off on its own. Removed the coupler which cracked when a sheet got stuck underneath it! Replaced coupler and new screw/nut combo, popped on agitator. That easy.

Pull the washer in order to have space to work on it, unplug the electric shut off the water and start to unscrew the top where the control panel is just be careful to not touch the electric parts like the chips because they are very sensitive to static that anybody have in hands. then ones is open unscrew the nut screws and take the old control off and put the new one in and plug the wires in the same place like like old one. Put the screws to hold the control panel and put everything together. then put the water on, plug the AC and try the washer on and since then is working.

Removed agitator by pulling up, wiggle to and fro, watch out for unexpected release. Agitator coupler was worn, stripped splines. 7\16 socket, long extension to remove bolt in coupler. Install new coupler, new bolt, then line up agitator to splines on agitator coupler and push to snap in place.

Replaced the sensing thermistor. It was necessary to remove the front and top panels to get to the location at the water inlet. The wiring diagram located in a pocket in the control panel actually had good instructions for the disassembly.

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.