WWXR4100T6WB General Electric Washer - Instructions

Replaced dual inlet valve. Problem solved

Unplugged washer. Shutoff water supplies. Removed control panel. Disconnected wiring to valve. Removed hoses from old valve. Removed valve mounting screws (x2). Installed new valve and secured with mounting screws. Replaced washers in supply hoses and reconnected hoses. Reconnected control wires. Turned on water supplies. Plugged washer into electric outlet. Tested. EVERYTHING WORKING SO FAR!!!

remove the agitator by just pulling it up, remove the bolt that hold the agitator coupling down and install the new one.

Found that the teeth and the agitator coupler hade stripped out. Replaced the coupling and everything worked great. 10 Min and $10. 00 Fixed it up.

There are many on-line videos to help you do this. It's so easy, even a beginner handyperson can do it. For this model, just run a strap under the agitator to assist you in lifting it up off the coupler (good tug). Remove the old worn coupler, put the new one on, set the agitator back on by giving it a little downward push.

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

Belt had worn and was shredding and melting due to pump not draining tub. Too bad my wife and daughters couldn't tell me the pump wasn't working right any sooner. The belts slow disintigration over time made a black, gooey mess inside the machine. Worked on the machine in place and only removed front. Old belt removal was easy with screwdriver prying around motor pulley but replacement was challenging in the tight space under the machine. It did go on by working-rotating belt around back of agitator pulley. By far the hardest part of the job. Replacing pump was easy enough but made a water mess and had to adjust clamps for leaks. Machine is now good to go.

As directed by the book.

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

Once I watched the video to replace the pump(Thanks so much for that - big help!!), I disabled the machine to replace the pump, to my surprise found a big clump of fuzzy stuff that was blocking the pump, once I removed that and re-assemble the washer, it started working fine!. Unfortunately, I had already bought the the pump and agitator bell thinking they where both bad, so I'm in the process of returning them now, thanks a bunch! btw - what took so long was I had a mess with the water left in the washer, tip - get all the water out first ;-)

Pulled up agitator, replaced coupling kit, pushed new agitator onto new coupling kit. Took less than 5 minutes if that.

This top loading washer was purchased new in 2006. It has had a good bit of use and was a rather inexpensive model, but had been working fine. Suddenly the agitator stopped working. First I pulled off the agitator inside the machine, which in this model came off in one piece. In order to do that I grabbed it at the very bottom by pushing my fingers underneath the base, then rocked it from side to side while pulling up on it until it popped off. This exposed the agitator gear that had gone bad. I unbolted the gear and pulled it off. This removal took a bit of effort, and again, we had to rock it back and forth while pulling up on it until it finally came loose. When the new part arrived a few days later, we slipped it onto the transmission stem, and bolted it into place. Then the agitator was put back on and snapped into place. Works as good as new for less than $14, including shipping!

Viewed the hot/cold valve. I saw that the cold water solinoid was burned. Ordered new valve and replace old valve. On my washer 4 screws held the switch panel, easy to remove and gave me plenty of room to veiw and do the repair.

I found the diagram in your website, identify the problem, order the replacement part and replace it in 10 minutes. Great deal, thanks.

Watch how to fix it on You Tube. Order the part I needed and fixed. Real simple. That is it.