Models > WWTR1802KW0 > Instructions

WWTR1802KW0 Westinghouse Refrigerator - Instructions

All installation instructions for WWTR1802KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWTR1802KW0
76-90 of 249
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lost the temperature control know

  • Customer: John from Pilesgrove NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.

Thanks
John S.

coil Iceing up

  • Customer: Thomas from Stuart FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

  • Customer: Larry from Newton KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

inside door rack was missing

  • Customer: Manuel from El Mirage AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
snaped right in.

Broken door self retainer bar

  • Customer: Linda from Cadott WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Received the retainer bar and pulled it out of the pkg. It seriously took less than 10 seconds to replace. Just snap it in place!

the freshfood door of refrigerator can not close.

  • Customer: linh from palmdale CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
take of the old gasket, clean and put the new one on ...that's it....so easy...

freezer worked frig was warm. Ice maker is still not working

  • Customer: steve from Kirkland WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

Frost in freezer, fridge not cold

  • Customer: Bob from Pinole CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

Broken bar and seal

  • Customer: Mark from Sandwich IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Snapped in the bars and with the seal once on the track went right on

Retainer bar on door snapped

  • Customer: Joe from Woodbridge VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
It's a pressure fit. Squeeze the ends and snap it in.

Bracket for door shelf broke

  • Customer: Mark from Woodbridge VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Ordered new bracket

Freezer built ice, fridge not cold enough and running constantly.

  • Customer: LUIS from CENTENNIAL CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.

2 of the 3 door racks were broken

  • Customer: KAREN from HOUSTON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 4 people found this instruction helpful
It was extremely easy. All you had to do was to pop them into place.

both ref&frez were hot

  • Customer: Gary from Dunnellon FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1 went with maj 69% said defrost timer. NO. 2 went with second choice run cap NO. 3 went with my thought, ( PTC Starter ) why not, most exp part. Fixed the problem.

freezer was freezing and no refrigerator

  • Customer: Michael E from Uniontown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instruction vedeo from partselect. THANKS!!!!!
All Instructions for the WWTR1802KW0
76-90 of 249