Models > WWSS2601KW1 > Instructions

WWSS2601KW1 Westinghouse Refrigerator - Instructions

All installation instructions for WWSS2601KW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWSS2601KW1
406-420 of 590
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The refrigerator's In-door water dispenser leaked water. The leakage started out slow and over a period of time increased.

  • Customer: Frank from Mentor OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

Installed a extra shelf

  • Customer: nathan from Buckley WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed the shelf pegs in the wholes

Broken freezer door shelf bins

  • Customer: Elmer W Maxwell from Kennewick WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Hooked them into place. No muss, no fuss. Bins were delivered in a timely manner, and they were the correct ones!

We were short space in the refrigerator

  • Customer: Jose from Reseda CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Installed the door bins, quickly and easily. I was very impressed with your quick delivery and your customer service. Also excellent, my whole buying experience was excellent. Thank you.

no water flowed to the ice maker

  • Customer: Levern from Mc Donald TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Replace water dispenser Actuator

  • Customer: Phillip M. from Melbourne FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the water tray. Remove 3 screws at bottom of cover with Phillips screwdriver. Slid frame upward, disconnect wires from door. Remove screws that held the water actuator. Took broken water actuator out, slid new one in. Screw in place. put parts back in place and bingo, all done. Easy!!!

"Popping" noise when opening the refrigerator door.

  • Customer: Alan from Plantation FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.

refer quit cooling and so did freezer

  • Customer: jerry from petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

2 door shelves broke

  • Customer: Ellen from Brandon FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple installation - just pop into place! We thought they were a bit overpriced, but we certainly can't complain about the service - EXCELLENT!

COULDN'T FINE WATER FILTER

  • Customer: Jacqueline from River Ridge LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
IT WAS EASY.WATCHED THE SHORT VIDEO AND PLACED THE PART RIGHT IN. THE PART CAME A LOT FASTED THEN WE THOUGHT. THANK YOU PARTSELECT.

Ice Maker Not Getting Water

  • Customer: Edward from Cuba NM
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Water Dispenser broke

  • Customer: Theresa from Clinton Twp MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions on video from Instance Repairman. Very easy to follow directions. He does step by step instructions.

Our refrigerator ice maker was broken, crisper draw was broken, and shelf support was broken.

  • Customer: Gary from North Smithfield RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

the brackets on the crisper tray broke

  • Customer: John from Lockport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
after watching the video I followed to the tee used the screw driver tapped out the old peg and removed the stem in minutes I was tapping in the new parts

Broken Crawer Cover

  • Customer: Orrin from Punta Gorda FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the old and put in the new! Piece of cake!
All Instructions for the WWSS2601KW1
406-420 of 590