WWSS2601KS1 Crosley Refrigerator - Instructions

Turned off water to refrigerator and unscrewed canister, removed filter reinstalled canister and ran water thru to get all sludge from line. Turn water back off. Remove canister and install filter reinstalled canister, turned water back on. Run water thru line. Job complete. No problems.

I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part

unplugged frig, removed shelves & inner lower back panel in freezer side, removed defrost thermostat from tube, cut the wires and spliced in new stat wires with provided wire splices crimped together and replaced thermostat on tube it has been a week and no ice so far??. this was after 2 trips by the repairman who replace the defrost timer board which was most likely good at a total of $160!!! still cheaper than $1000 for a new frig!!!!!!!!!!!!!!

Pooped the old one out and pooped the new one in.Item was in stock, very fast delivery.

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

Just slipped the bin in place. Very easy. Took less than 2 minutes

tapped the two support into the side of frigde and placed the crisper drwers on them and was done. next had to take six screws on on front of door where the water and ice come out take broke one out and snap new one in about 15 mins done. everything was simple and easy.

This was the second time the part had failed and it was time to replace it. Rsther than hope a local store may have the part, I went on the internet and found PartSelect.com and ordered what I thought was the right part and it arrived here in Texas the next day! Turned out to be the wrong part. Oops! I contacted PartSelect by email to see if I could return the part and got an imediate response from Denise with the address ad instructions for returning the part and a very generous offer to help select the right psrt. I gave her the refrigerator/freezer model number and she immediately respoded with the part number. I rerordered the part and it again arrived the next day. I slipped it into place on the refrigerator door and it fit!! End of problem but not quite the end of the story. I received an email a couple of days later informing me that the money due me from the first order was on it's way. Color me a very happy customer!!

thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.

I removed the broken bin and replaced it with the new one

When my wife and kids moved down they lost the upper bracket and the screw for the lower cam. parts show up and matched perfectly to the orginal no issues at all

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

What would have been a simple job I made hard by pulling the water hose out of its place that was the hardest part about putting the ice dispenser back in, it took me about thirty minutes to put it back I !

Open door - popped it in - done

pulled the old seals off one at a time and starting from the top of each door, pressed the top edge of the seal into the groove, using the quik clamps to hold the top in palce at each top corner, went down each side of the door and pressed the seal into the groove, when I reached the bottom, I moved the clamps to the bottom and used thm to help press the seal into the bottom groove, Each door took about 15 min.