WWS833FS2 Crosley Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer tub enables after end of spin cycles
Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.
Parts Used:
-
Celeste from YAKIMA, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water would not completely drain and go to spin cycle and noisy while trying to drain.
I ordered pump so I would have it on hand. I didn’t want the washer in pieces waiting on parts. New pump came in 2-3 days with standard shipping. Found a video online for this model. Removed top. Removed control panel and set on front edge of frame. Removed door seal spring. Removed front panel and separated seal from drum. Pump located at bottom left. Removed pump screws. Got a shallow pan from kitchen to catch water. Removed hoses and trap. Not much water. Took trap boot and pump to sink for cleaning and found a bra wire had made it past the screen and was rubbing on pump impeller. That was the noise. Cleaned and reinstalled old pump. Has been running for 2 months without a problem. Easily returned the new pump! Highly recommend this company and site. Will come here for my repair jobs first. Hope I remembered all the steps correctly since it has been over 2 months.
Parts Used:
-
Tim from DEFIANCE, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer pumps and drains but does not agitate or spin.
Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.
Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.
Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.
I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.
Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.
Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.
I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.
Parts Used:
-
DENNIS from EATON RAPIDS, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain pump froze during subzero temp
Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done
Parts Used:
-
Buford from LAWTON, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stripped threads.
-
THOMAS from Zephryhills, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dirt particles on clothes
-
Frank from Ormond beach, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Off/on knob broke
-
Barbra from Mills River, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt broke
-
Dave from Murrieta, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor burnt out
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
Parts Used:
-
ANNA from STATEN ISLAND, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't drain completely and wouldn't final spin
before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.
Parts Used:
-
frank from fostoria, OH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
worn belt and broken lid strike
The longest part was cleaning and taking the washer apart , the screws were rusted to the bottom of the washer front,had to spray and pound on screws to get them out.after cleaning dirt and rust in the washer I greased the idle pulley.Putting on the belt was a snap.I also had to repair a leg screw that keeps the washer level, Washer runs like a new washer. very Pleased with the results. Its like having an old washer restored to new. it looks and sounds like a new washer.It took less then 5 mins to change the lid strike.
Parts Used:
-
Linda from Scio, NY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
We smelled rubber burning when I did laundry.
-
Willie L from Sledge, MS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Parts Used:
-
Gregory from Piscataway, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
The water would not drain or spin out all the way
Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.
Parts Used:
-
sherry from ellenburg depot, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water would not drain or washer would not spin
Pulled off back panel and found that the Drain pump had some how came loose, so I found screws and tried but still wouldn't work check pump for blockage couldn't find and but could hear the pump hum so figured the pump went bad. the hardest part was getting the squeeze type clamps off or it would have been a 30 minute job. I orederd new part and it came fed ex next day and put in and changed the bellows clamp to worm gear and made it a lot easier going in. Started washer and ran just like it was supposed to.
Parts Used:
-
William from Amanda, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!