WWS833FS1 Westinghouse Washer - Instructions

The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.

I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

Just pushed the knob on to the metal on-off control,

watched the video on website, printed instructions for feedback.

sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).

replaced it with the new one

One day the washer would spill water out on the floor then it would be fine for a week and do it again.Finally it broke,i ordered the new drain pump and installed it in just a few minutes,Hose clamps were a pain,it works just fine now,I would say replace the clamps while you are doing this ,it would make it much easier .Hope this helps !

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

removed and replaced pump

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

watched the video, all instructions were perfect!

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

Firs things first - get as much water out of the basin as possible using a siphon or a container and a sponge. Have towels ready for inevitable spillage. Dispose of water in a toilet. Remove the front panel of the washer. The pump is attached with 2 screws/nuts. Remove the pump and place in an empty bucket. Then remove the hose clamps from the washer inside the bucket to catch any water left in the hoses. Attach the new pump to the washer. Then attach the hoses to the new pump. Replacement is very fast and easy - total time from setup to testing, to cleanup 1.5 hours.