Models > WWRG5700KW0 > Instructions

WWRG5700KW0 Crosley Dryer - Instructions

All installation instructions for WWRG5700KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWRG5700KW0
241-255 of 342
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer just barely got warm

  • Customer: J Martin from Guerneville, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.

no problem

  • Customer: David from Mayfield, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
put door catch in hole

banging noise

  • Customer: gordon from creve coeur, IL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed vidio instruction which made it easy

Loud squealing noise until dryer heated up - then quiet

  • Customer: Ernest from Stockholm, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
purchased bearing kit

The Rear drum bearing kit had sheared off

  • Customer: Amy from salem, OR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

timer knob was broken

  • Customer: Virginia from Hopewell Junction, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just pushed the new knob on. Actually took about 30 seconds. Works perfectly.

Dryer squeals while running

  • Customer: Jill from Norfolk, NE
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I wanted to know why my dryer was making such an ear-piercing screech. Googled, and found Steve at PartSelect. After watching the 10 minute video on how to replace the rear drum bearing, I knew this was something we could do at home. I ordered the parts on Friday and they arrived on Monday. Also ordered a new drum belt and drum glide. Didn't know if we would need those parts, but figured while we had the dryer apart, we might as well replace them. My husband watched the 10 minute video the following Saturday, and together we replaced all 3 parts. The original bearing was small enough to fit through the hole (which it shouldn't) and metal shavings we all over the plastic holder. The large metal ball attached to the dryer had grooves worn into it. The kids we amazed, too! I can't believe the repair was so easy! Seeing the inside of the dryer makes me wonder why they cost so much! Do not hesitate to make this repair yourself. Even just one person could do it.

Dryer Won't Heat Up

  • Customer: Michael from Los Angeles, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

Rear drum bearing failure

  • Customer: TonyMac from Alamo, TN
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum

  • Customer: Witly from Wheatley Heights, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I remove the drum, and install the bearing just like the instructions in the video.

Drum Squeeking

  • Customer: Mark from Aurora, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Replace the Drum Bearing and Shaft

dryer would heat up but shut off too early

  • Customer: D from Oak Park, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

dryer started to squeal when started

  • Customer: Niel from Howell, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

squeeking & thumping noise

  • Customer: Thomas C. from Manahawkin, NJ
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Scraping noise at rear of drum

  • Customer: Bruce from Roscoe, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.
All Instructions for the WWRG5700KW0
241-255 of 342