Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWGF3004KWC

WWGF3004KWC Westinghouse Range - Overview

Get Parts and Repair Help for WWGF3004KWC

If you know the range repair part you need, you can browse the list of all parts on the WWGF3004KWC, or you can search by name or part description. You can also find your part by where it is located on the WWGF3004KWC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the WWGF3004KWC

[Viewing 6 of 6]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$27.54

Natural Gas to Liquid Propane Conversion Kit

This kit is used to convert your appliance to liquid propane.

$22.70

Light Bulb Lens

The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.

$8.18

Anti-Tip Kit

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, ...

$8.68

Rear Drawer Glide

This rear drawer glide, also known as a storage drawer glide, is used in ranges. This helps hold the front side of the storage drawer and allows the drawer to easily slide in and out of the range. If your glide is damaged or missing, replacing it could solve any difficulty using the drawer. First, remove the storage drawer and locate the rear glide on the side. Next, remove the glide by taking out the screws. Replace new glide by placing tabs into the cut-out. If you are replacing both rear drawer glides, then repeat the same on the other side. Refer to the diagram provided by the manufacturer for further installation instructions and guidance.

$8.68

Front Drawer Glide

The front storage drawer glide on your range is mounted on the side of the cabinet. The purpose of the drawer glide is to support the storage drawer from the front. If your front s...

$89.40

Bake Igniter

The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.

$31.57

Door Handle

Screws are not included.

$5.02

Steel Washer

This steel washer is also known as the range washer and is used on your oven door. The measurements for the steel washer are a three quarter inch outer diameter, and a one quarter inch inner diameter. This washer is an OEM part, made of steel, which is sourced directly from the manufacturer. This specific steel washer is used with your range, to secure the inner and outer door together and to secure the oven door handle back in place. Users have ranked this repair as a simple installation that should take you less than fifteen minutes to complete.

$8.15

ORIFICE

$55.67

Oven Door Cap - White

This part goes over the top of the oven door glass. The door handle also attaches to the door cap.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bought a new gas oven that did not come with a propane conversion kit.

  • Customer: Denny from Bishop, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench set
  • 110 of 157 people found this instruction helpful
I followed the simple instructions that were included in the kit. I started by replacing the 5 orifices on the top burners. The orifices are well labeled with numbers and colors. Next, I tightened the broiler burner orifice and the oven burner orifice with a 1/2 inch wrench. I had to tighten them pretty good to get the flame down where it is supposed to be. ... read more

Stove was set up for natural gas and needed to be converted to LP

  • Customer: Ed from Orange, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 112 of 181 people found this instruction helpful
The LP conversion kit contained very good, detailed instructions. I replaced the gas orifices, took off the bottom door and adjusted the regulator.

Used the screwdriver to adjust the low flame and everything was done. read more

Oven light receptacle broken - bulb base broke off

  • Customer: Paul from Spokane Valley, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 37 of 44 people found this instruction helpful
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snap... read more