WWGF3000LWC Westinghouse Range - Instructions

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

It was a replace racks not repair. No problem

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

Unplug the range, remove racks. Remove 2 screws from the bottom back corners ( this was the hardest part. I used a stubby screwdriver, but a longer one would be better. They are fairly long screws). Remove oven bottom, lifting from the rear. Remove burner cover. Bottom left corner is a triangle cover. Remove this too. Remove the 2 screws holding the old igniter in place. The igniter unplugs easily. ( I used pliers, the plug has a clip, and pliers grip better.) Install new igniter ( it only fits in one way ) reinstall mounting screws and covers. Replace oven bottom. (I didn't replace the 2 screws. The bottom sits solidly, and they are a bit of a pain.) Plug in, set clock, test for oven to fire up.

I repaired with the use of 1 Phillips & 1 flathead screwdriver. It was very easy.

Open oven door and remove metal splash plate on bottom of oven by removing two screws in back.
Remove heat distribution plate (metal) by unscrewing a single nut with pliers.
Now the ignitor is visible. Unscrew old ignitor by backing off two screws.
Detach the wires and reattach to new ignitor. (a cover plate may have to unbolt from the left back corner to get at one of the wiring connections.)
Reattach new ignitor and then flame distribution plate.
Put on splash cover and tighten back screws.
Test oven, it should light within 1 minute.
All is done.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Easy as pie. I had the new part in my hands in less than 48 hours. Fortunately for me it was a simple fix and I was literally cooking in under 15 minutes. I was a little worried about doing anything to a gas stove, but by looking at the other unbroken side, it was just a matter of snapping together a new assembly. What a wonderful website!

1)First unplug range.
On inside of oven, there's a copper, pen-like object connected to a copper wire. 2)Open the clips on side of oven that hold the pen-like object(the probe.)
3)Open the lid of the stove. On left hand side, there's a hole through which to pull the copper wire and probe out of the stove. Or you can just as easily use wire cutters to cut off probe and just pull wire from the oven through the hole. 4)Pull off the oven's thermostat control knob. Using screwdriver, unscrew both screws under where the knob was. 5)Now pull the flat wire connecters from both sides of the old thermostat. Remember which wire goes on which side.
6)Remove old thermostat and copper wire that's connected to it.
Replace thermostat. 7)Feed copper wire with probe through hole on left side of stove.
8)Slide flat wire connecters onto sides of new thermostat. Replace screws. Insert new probe into clips on side of oven. Close stove cover. Replace thermostat control knob. Plug in range. Test thermostat. 9)According to owner's manual, turn oven to 350° and oven should be no more than 50° above setting.

Need the thermostat now

1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.

2. If possible, remove the storage drawer for ease of access.

3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.

4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.

5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.

6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.

7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.

8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.

9. Reattach the drawer if necessary and plug the range back in.

10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Partselect always have their install video with the parts they sell so it was easy. I know contractors must not be happy with people like partselect and YouTube with all the instructional videos they supply us with. Keep up the great work partselect.

remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble

It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.