Models > WWBD2400HW1A > Instructions

WWBD2400HW1A Westinghouse Dishwasher - Instructions

All installation instructions for WWBD2400HW1A parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWBD2400HW1A
286-300 of 311
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Top basket kept falling off the track

  • Customer: Daniel from Syracuse NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed the eight rollers that are screwed into the inside of the dishwasher upper section and simply screwed in the eight new ones. Only took about 15 minutes for the job.

Dishwasher didnt drain properly and the lower arm got stuck .The dishes did not come out vlean

  • Customer: Lois from Naples FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the old one..snapped in the new one.Done

The close door code kept going off and was leaking on the bottom.

  • Customer: Roseana from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the gasket off and put the new one on.

broken pump

  • Customer: EDGARDO from NEW YORK NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
By tilting the dishwasher over, I was able to remove the old drain pump and install the replacment pump. Only a small screwdriver was need.Took less than15 minutes.

Lost several wheels from lower rack of dischwasher

  • Customer: Peter from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Nothing to it. Just inserted the iron stud into the center wheel and pressed the bracket onto the stud.

Not enough water to clean dishes

  • Customer: Thomas from Winter Springs FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I used the flow chart online to determine the water inlet valve (WIV) was probably the problem. 1: Cut the power (circuit breaker) 2: turn off the water 3: Removed the lower, front panel (depending on age, you may want to replace the screws) 4: Disconnected electrical cord, waste water line and fresh water supply. This is when the bucket comes in handy. The waste water is NASTY!. At this point, I pulled the DW out and rolled it on its side (Bucket time). I removed the defective part and replaced it easily Simple swap. Clean the old teflon tape off the threads and put fresh tape on. Then I reversed the instructions and opened the water. Check for leaks before you finalize the installation. Then power it up and run a cycle to test. I took a coffee cup and put it in the top rack right side up and checked it periodically. If it keeps getting filled up, it's working. Then i ran a dishwasher cleaner through it, as it had developed a case of the crud sitting still. The new part is quieter than the old one, I can't even hear the water running into the DW now. I am SO happy that $30 worth of parts kept me from spending $500 on a new DW. Thank you Parts Select!, your installation video is great.

Rat chewed thru the drain HO9SE

  • Customer: Mahlon from Kirby TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
pULLED THE WASHER FROM THE COUNTER disconjnected the house from the garbage disposal connected thenew hose to the disposal, remove other end of old hose from thedishwasher and replace with the new drainage hose.

The old dispenser lid wouldn't snap shut.

  • Customer: Julie from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the you tube video posted on your site when I was trying to order the part. It showed me exactly what to do. I just had to turn off the power to the dishwasher, take off the dishwasher door cover, unplug some wires, unscrew the old dispenser, and install the new one by redoing everything I had just undone. As a single mom, I was quite pleased to have done this myself. It saved me atleast $100 in a repair bill.

Water was leaking from under the Dishwasher. Inspection showed problem appeared to be a cracked solenoid water inlet valve

  • Customer: Stephen from phila PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Water was leaking from under the Dishwasher. I took the lower front panel off to peak under the dishwasher with a flashlight to see if I could identify the problem.the leak appeared to be a cracked water inlet solenoid valve. I tuned off the water at the shutoff valve under the sink. Upon delivery of the replacement I disconnected the supply line from the compression nut of the brass Dishwasher Elbow with an adjustable wrench. Next I unscrewed the DW elbow from the water inlet valve using an adjustable wrench and a Channel Lock Pliers. Next remove the mounting screws holding the inlet valve in place and it dropped down allowing me to pull the electrical quick connect off and use a pliers to disconnect the fill tube. The process was reversed. Remount the hose to the new solenoid valve. Connect the electric. Remount the valve with the 2 mounting screws. Use Teflon tape to reinstall the DW elbow. Use pipe dope to reconnect the water supply line to the compression nut side of the DW elbow. Turn on the water and run Dishwasher to confirm repair is ok. Remount lower access panel and smile. Job well done. Exactly as shown in the video.

Water inlet valve leaking

  • Customer: Robert from Flowood MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
first shut-off power and water! removed bottom cover panels and top two mount screws from DW. slide DW out about one foot for easier access. disconnect inlet valve wiring harness. then remove the screws that hold the unit to the dishwasher. then disconnect water outlet hose (mine was a black accordian type tubing) use your pliers to move back the clamp. it will take a little bit of twist and pull to get that hose off. next use your adjustable wrench and pliers to unscrew inlet copper tubing from the valve unit. the old valve should now be free from the DW. replace in reverse , remember to use silicon tape. I left the bottom panels off for a couple more days to check for leaks. my wife told me that the first washing after the fix did not really clean the dishes as well , but after that everything was back to normal. so perhaps run the machine empty once?

Dishwasher leaking

  • Customer: Lauren from Marietta OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old gasket,placed new one on pressing into place.Very quick and easy.Saw the youtube on how to do it.Unfortunately this was not the problem.now have a new dishwasher same brand.

Broken door spring.

  • Customer: Keith from Manitowoc WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
After watching the video the replacement went very easy. The only thing I would suggest is that you replace both springs to equalize the tension.

Dishwasher leaking from underneath unit

  • Customer: Keith from Meansville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Spotted the source of the leak at the first heating element under the dishwasher. Removed the brass mounting nut and it was cracked. Replaced with new part from PartSelect.com and the leak was fixed. Apparently the heating element gets so hot it tends to crack the mounting nuts, which results in a leak. Delivery time for part said 3-5 days - mine arrived one day after ordered!

Water leaking

  • Customer: Ron from Brick NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the old part and replaced with new. Done

Water leading from bottom of door

  • Customer: Henry from S Burlington VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just like the instruction video. I pulled the old gaskets out, cleaned the gunk that had accumulated and put the new gaskets in. The tub gasket does not require any cutting or stretching. Just make sure it makes the turn at the bottom of the tub so the door seals properly. The door gasket was very simple to replace.
All Instructions for the WWBD2400HW1A
286-300 of 311