Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWBD2400HW0 > Instructions

WWBD2400HW0 Westinghouse Dishwasher - Instructions

All installation instructions for WWBD2400HW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWBD2400HW0
31-45 of 311
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Soap dispenser wouldn't open until the very end of the cycle

  • Customer: Laura from St. Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!

Door spring had broken; door would fall open

  • Customer: Sue from Weymouth, MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 10 people found this instruction helpful
Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.

Striker

  • Customer: Jeffrey from Mildland, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 16 people found this instruction helpful
Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple.

Thank you for stocking the parts and shipping them as promised.

Lower spray arm pop out and broken

  • Customer: YUAN from ROWLAND HEIGHTS, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
Only took me 5 sec, just push it in. Good as new. Thanks for the fast deliver .

malfuction due to soap buildup and worn release

  • Customer: Matt from Sandy, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.

Heater Element Covered in Mineral Deposits

  • Customer: Chad from Cypress, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a few weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.

Water leak underneath dishwasher

  • Customer: Richard from New Orleans, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 9 of 10 people found this instruction helpful
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Water leak behind kick-plate

  • Customer: Larry from EDWARDS, CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 11 of 16 people found this instruction helpful
Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

water leaked from the center of the door

  • Customer: Bradford from Secor, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 8 people found this instruction helpful
DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

Dishwasher wouldn't drain after cycles.

  • Customer: Thomas from Bismarck, ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 9 people found this instruction helpful
Old pump impeller (internal to pump/motor part) snapped into place, but snapped out of place after warranty.

Disconnected power. Removed bottom spray arm and strainer. Siphoned out remaining water. Removed hoses and two mounting screws on pump. Removed wires. Removed pump.

Installed pump in reverse steps.

the valve stuck closed - no water would enter the machine

  • Customer: Richard from Fox River Grove, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 9 of 12 people found this instruction helpful
remove vanity panel
disconnect copper supply line from valve
remove valve mounting screws
rotate valve to access hose clamp
loosen clamp and slide up rubber tubing about 2 inches
pull hose off barbed fitting and remove old valve
reverse order with new valve

dispenser cap latch broke

  • Customer: Michael from Moreno Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the door, facing inside. The bottom screw on each side. Thanks for all the help.

Spray arm came off and melted on coils

  • Customer: Susan from North Wales, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 10 people found this instruction helpful
took it out of the bag and snapped it in. Less than 10 seconds.

leaking dishwasher

  • Customer: Mark from port matilda, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

A hole in the dishwasher dicharge hose.

  • Customer: Lee from Columbus, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 17 of 38 people found this instruction helpful
I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.
All Instructions for the WWBD2400HW0
31-45 of 311