Models > WWBD2400HW0 > Instructions

WWBD2400HW0 Westinghouse Dishwasher - Instructions

All installation instructions for WWBD2400HW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWBD2400HW0
241-255 of 329
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dishwasher was leaking.

  • Customer: Michael from Noblesville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the bottom gasket and the tub gasket. replacing them both was very easy. I pulled the tub gasket out by using a screw driver and popping out a section then pulled it out. Installed new one by just pushing it in. Bottom gasket was simple as well. There was a notch in the gasket on the right side so you can't screw it up on which side goes where. Pulled the old one out and pushed the new on in. I found it easier to install the right side with the groove first. Both gaskets helped. However dishwasher was still leaking. Another person had mentioned that the spinner that shoots the water on the bottom, had a hole in it and was shooting water towards the door. I examined both of them and found that the bottom one had a bigger hole on the very end. It looked like it hit something and made the hole bigger. I temporarily put duct tape over it and it has't leaked. Plan on ordering the new part today.

melted hole in lower arm

  • Customer: Jon from Lafayette CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
ordered and replaced in 5 minutes

sprayer arm came apart

  • Customer: jeffrey from North Richland Hills TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just had to remove arm and reinstall the new one.That is not hard the great thing was that I tried to call sears repair store,45min.no answer so I drove to it. They didnt have part but could order it from frigidaire would take 10 days and 12.99 shipping. I came home checked Frigidaire website, same price and shipping.Then I looked on your website part was half the price and less than have for shipping. Received the part in two days and that included New Years day. Excellant business and super savings.thanks

Dishwasher was leaking water onto the floor

  • Customer: miles from hoboken NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I viewed a very short video on how to replace the lower gasket on the website which was extremely useful. I then ordered the part via standard shipping and it arrived very quickly. I used the flat head screwdriver to gently loosen the old gasket which has mineral buildup on it and was stuck into place. Sliding the new one in was a snap. This was one of the best sites as you could search for the part by describing the problem. I would definitely use it again!

Water leaking from the washer

  • Customer: Charles from Mount Pleasant TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
R&R the tub gasket and the door gasket. Repair not effective, it still leaks.

Water leaking from bottom center of door

  • Customer: James from Pollock Pines CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Ordered a bottom gasket and replaced it. Started dishwasher and had same leak. Found out that the lower spray arm had a hole in it from the heating element and was spraying water directly at lower part of door. Replaced lower spray arm, problem solved!!

spray arm broken

  • Customer: Almir from Forest Hills NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old part and slide new one in , so simple

Dishes still dirty after wash cycle

  • Customer: Janet from Milton VT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the filter on the bottom of the dishwasher. The PartSelect website walked me through the whole thing. Thank you!!!

dishes not drying -- water not heating

  • Customer: Judy from Miles City MT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took bottom panel off dishwasher -- used stubby screwdriver to remove bracket from old thermostat, intalled and connected new thermostat, replaced bracket -- easy. Parts schematic on website made locating and replacing part very simple.

water leak at bottom of door

  • Customer: Raymond from Port Clinton OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out bottom gasket, inserted new gasket. Max about 5 min. Pulled out tub gasket,cut new gasket to match old gasket and pressed into tub.Max about 10 min. Spent more time putting kick plate back on.

Dishwasher was leaking from the bottom of the drawer

  • Customer: Louis from Waterford NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The bottom gasket slid straight out, after which I cleaned the slot a bit, and the new gasket slid in perfectly. The tub gasket pulled out by hand, and again, after wiping down the groove, I easily fit the new gasket around the tub and trimmed a few inches from one end. There is no longer a problem with leaks, and I think the door closes a bit more securely as well.

Heating Element Replacement

  • Customer: Nathan from Pittsburgh PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1) Shut down power to dishwasher at circuit breaker. 2) Remove front panel from bottom of dishwasher. 3) Remove two screws on valve mount to allow for more room to work. 4) Remove electric connections on heating element. 5) Remove terminal nuts on heating element. 6) Open dishwasher and remove lower dish rack. 7) Remove heating element by pulling up and removing element from the clips. 8) Insert new heating element. 9) Perform the above steps in reverse order, from 7) to 1).

Water inlet hose replacement

  • Customer: Frederick from Patchogue NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The hose goes from the water inlet solinoid to the side of the dishwasher.Remove the kick plate from the bottom front of the dishwasher. Disconnect the water supply to the inlet of the solinoid valve (copper tubing on mine). Remove the screws under the counter top which hold the dishwasher in place. slide the dishwasher out from under the cabinet only as far as needed to expose the hose(about 1 foot). The hose is behind the insulation. Remove the hose clamps from both ends of the hose(solinoid outlet and side of dishwasher)Remove hose carefully because this is all plastic. Install replacement hose and clamps. The new hose is several inches too short and will not fit into the upper hose guide, just bend it underneath. Be sure to put hose in lower keeper on side of dishwasher. Attach clamps, tape insulation back in place, slide dishwasher back under counter and install screws under counter. Attach copper tubing to water inlet solinoid valve. Run dishwasher and check for leaks. Replace kick plate. Note: I had enough loose electrical wire to slide my dishwasher out. If you don't have enough wire to slide out the dishwasher you should call a repair man.

Rinse aid cap melted

  • Customer: TAMINIE from CODY WY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered a new one.

Water leaking from door

  • Customer: Mark from Amarillo TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Instructions link was sent with the invoice that were dead on. The instructions and video were so comprehensive that any elementry school age child could perform the repair like a pro. Good Job Part Select!!!!!
All Instructions for the WWBD2400HW0
241-255 of 329