Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWA8344VKL

WWA8344VKL General Electric Washer - Overview

Get Parts and Repair Help for WWA8344VKL

If you know the washer repair part you need, you can browse the list of all parts on the WWA8344VKL, or you can search by name or part description. You can also find your part by where it is located on the WWA8344VKL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WWA8344VKL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.54

D-Shaped Knob Insert Clip

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start...

$3.50

Timer Knob Clip

The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip. If the timer does not advance or the washing machine will not start, this may also be a symptom of a damaged timer knob clip. This part is clear plastic and is about 1 inch in size. Many of our customers have rated this repair as easy, and the only tools you may require are a set of needle-nose pliers. This is an OEM part sourced directly from the manufacturer.

$7.32

V-Style Drive Belt

This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise....

$2.06

Screw

This screw is sold individually.

$16.33

Timer Knob with Clip

$10.69

Compression Ring

This compression ring works in conjunction with the timer dial.

$5.13

SCREW-PKG 12

$16.81

Water Inlet Valve with Outlet Insert

This washing machine water inlet valve has two ports for water to enter.

$7.63

Hose Clamp Kit

This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of t...

$30.59

Agitator Coupling

This coupling is used for 20 spline drive shaft transmissions.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

GE washer no spinning during spin cycle

  • Customer: Laurence from Bronx, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 145 of 160 people found this instruction helpful
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Lo... read more

washer was not agitating or spinning

  • Customer: Rachelle from Kent City, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 52 of 56 people found this instruction helpful
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off and putting the new b... read more

Replaced the Agitator coupling

  • Customer: jose from lAREDO, TX
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 42 of 53 people found this instruction helpful
First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was a little hard to i... read more