WWA8314PML General Electric Washer - Instructions

Pulled top off and removed corner mounting plate then unscrewed mixing valve.replace wiring to valve and mount new valve in it's place .put back support and corn brace .then attached hoses and put back in service .work great for 20 plus yr machine.thanks tom

removed 3 screws from the back. Then removed the little water line clamp. unplugged the 4 wires. took the new part. plugged it in. put on the water line clamp. put the 3 screws back on. put the hoses on the back again. turned on the water supply. and started washer.

I took the back cover off of the washer, studied my next move and jumped in.Easy Lou-eezee!

Did some checking to make sure the filter, screen and hose were unobstructed. Turned off water at faucets, disconnected hoses and drainage hose. Unplugged machine and pulled out far enough to access back. Used nutdriver to remove 6-7 screws that held the back on, and then inlet valve plate. Removed clamp on outlet hose, then one by one removed wires, making sure to connect them to the same connections on new valve. Re-connected outlet hose and reversed procedure. Easy fix. Went ahead and replaced hoses while I had it out.

Took off the backing and then the water inlet piece and just reverse the procedure when installing the new part. What really amazed me was the ease of ordering the part through this website. I found it, ordered it and in two days it was here!! Great website, you folks really know what your doing. My repair was under 25 dollars, how much would have I paid for a service tech to come out, don't even want to think about it !! I'm telling everyone I know about your website. THANKS AGAIN !!!!!

Removed existing knob by using pliers to release clip from shaft. Inserted new knob (with clip attached) onto shaft and aligned with shaft groove to engage clip. Easy breezy.

Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.

Since the valve sprayed water out in one particular spot, it was easy to determine what part I needed. After I received the part from "Part Select" it was super easy to replace and took about 10 min. and the washer was good as new.

We bought this used Hotpoint that was probably one of the original machine created back in the stone-age, it's so old. We've had it 10 months, and it's always had this... burnt rubber stink to it... then one day, it stopped agitating and sounded like a metal bucket of bolts being shaken. We're on a military income with five kids, and the idea of buying a new washer was just... heartbreaking. On a whim, having fixed a washer once before, we opened the front up and painstakingly pulled every last rubber fiber from what used to be the belt. Ordered the part. It shipped quick, arrived quick, and in under a week we were back in business. Someone else had mentioned the needing 1/4" socket, and I was glad I remembered that, because it made is SO much easier.

Unplugged washing machine from electrical outlet. Turned off water supply to washing machine. Removed inlet hoses. Removed 2 screws to get panel off that water valve attaches to. Removed the panel for access to water valve. Removed fill hose from water valve and then unbolted valve from panel. Made diagram of electrical wiring to ensure correct placement on new valve. Attached new water valve, electrical wires and fill hose to valve. Installed panel in machine and hooked up inlet hoses. Turned on water supply and inspected for leaks. Turned on washing machine to verify filling and repair was OK.

Replaced the water inlet valve. Your shipping was next day the best I have ever received. Thank You

Very straight forward install. First removed the agitator itself by pulling straight up on it. Then removed the agitator coupling without the need of any tools just pull it straight off. Install new coupler and agitator.

An older gentleman neighbor needed help finding a part for his machine. We checked local parts stores to no avail. I researched the internet, found your site and ordered the part. My adult son put the part on in less than 15 minutes. Our neighbor was very happy. We will tell any one in our neighborhood to order parts here. We followed the part watching UPS. The part arrived at the exact day and time. It couldn't be easier.

Once I figured out what was wrong (splined, hard rubber part of the agitator coupler had parted from the inner, metal part)the job was easy. But I couldn't really tell what was going on until I saw the new coupler ($31.25)which I didn't even have to use. What I did was rough the outside of the metal core with a coarse file, score the inside of the outer, hard rubber part with a screw driver, clean both surfaces thuroughly and reassemble with JB weld. Let sit for 24 hours, and voila. If I had to do it again I could do it in half an hour (not counting glue set-up time).

Gently turned washer over onto its front. Removed bottom metal panel (3 or 4 screws on each side). Removed old belt. Installed new belt. NOTE: The new belt is a tight and perfect fit, therefore it will not want fit on to both pulleys/ rotating discs. I have found the best method is to start the belt on the disc that drives the belt. Then place as much of the belt over the disc that sits below the washing machine drum as is possible(the spinning part)and then turn the belt by hand and the belt should pop on to the disc. If the belt goes on easily you may have the wrong belt as the belt must be tight to achieve the traction necessary for the washing machine to spin. HOPE THIS HELPS!! A screwdriver may be handy in helping to pry on the belt. Good look.