WWA7050GAL General Electric Washer - Instructions

I changed the Water Inlet Valve in less than 15 minutes. The valve fit exactly, and the water hoses fit right on. I turned on the water and the washer filled without hesitation. The cost was 15.00, this beat the 62.00 price I was given by GE for the part alone.

This is the second time I have replaced this part. This time, I knew exactly what to do...the first time took longer. We have hard water here and also sediment in the water. Over time, the valve will not shut off the water.

Shutting off the water and unplugging the machine, and opening the back of the washer (every screw was the same size, thankfully. I didn't have to change socket sized) First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and then I unscrewed the hose clamp and I then pulled the element out about 3 inches and disconnected the two wires one at a time. I reconnected each one as I disconnected it from the old one. That way I knew I had it attached to the correct post. Reconnected the hose and reclamped it. Then I reattached the unit back into the washer and rescrewed everything back in place. The washers, I put in the end of the hoses before reattaching to the faucets. Attached the hoses to the machine and plugged it in the outlet.
It has been working ever since! (of course, I knew it would!) This machine is 25 years old and still going strong!

turn off water outlets, unplugged unit then removed water hoses, then removed the screws from the plate on the washer then removed the valve from the plate then unscrewed the clamp for the water inlet to the washer then removed the hose. then carefully removed the wire clips putting each one on the same connector on the new valve, then put everything back like I did when I took it apart and it works great.

I did watch the video, that Parts Select included in an email. After that just follow the instructions in the video. You do need two people to do the job, since the belt needs to be tight. One for holding and one to tight the screws.

Could smell burning rubber as it tried to spin, so figured it was the belt. No, I did no do it the hard way by removing the screws etc. I threaded the belt on the pulleys on one side, and slowly turned them, using my fingers to force thread the belt into place. Worked like a charm.

Unfortunately, this washer doesn't have a front panel: to get to the belt, removed the back panel. Unfortunately, you can't get to the belt from there either, unless you turn the washing machine upside down. Since the top of the washer is not level (control panel sticks up), the washer needs to be tipped upside down onto something the washer lid rests on, but keeps the control panel off the ground. We used...a sled. Unfortunately, since it didn't drain the last time used, even though we bailed the tub, there was still a fair amount of water that drained out once upside down. This is a heavy washer - took 3 of us tipping it over carefully onto the sled. We unbolted the motor, put in new belt, but needed to put a piece of the shifter arm assembly in place, which came loose. Took 2 sets of hands to accomplish all this. Works now - 2 small loads of laundry done successfully.

I emptied the washer and unplugged it from the wall. Then i pulled it out so I could get behind it. Next unscrewed the water hoses from the washer. Removed the plate holding the water inlet valve by unscrewing 2 screws holding it to the machine (I used Vise Grip/pliers). Note which side of plate goes up/outward so you can put it back on! Removed 2 more screws that hold the valve to the plate. Remove clamp from valve end to disconnect valve from tubing with a screwdriver. I was able to remove the tubing with a twisting motion even though my washer is way over 10 years old. Remove 4 electrical clips from the valve by pulling them out, (REMEMBER the order of the electrical wires!!). Install new valve by doing this in reverse. Then run test cycle, success and saved hundreds of dollars!

i Had washer up side down took puly out and transmission seal out used screw driver install your part add seal on it tap it back in used socket added quartz of gear oil90 as recommended put every thig back it good experience and saved hundreds of dollars for new ones thank so much for ur video and ur technical people on your site

After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY

I followed the instructions on your website to diagnose the problem, select the part needed for the repair, and fix the problem. Everything was as described in the video.

I looked up the part on line, ordered it and installed. Veru easy since the part that needed repair was right out in the open.

Replaced the water control valve (the thing the washer hoses connect to on the back of the washer) There were 3 bolts that had to be removed and once the part was loose, there were four wires attached, I disconnect each wire from the old part and reconnected to the new part at the same time to keep from getting the wires mixed up. Then I bolted the new part back in place...worked perfect. Total cost of repair was less than 30 bucks...

Turns out it wasn't the belt. The belt was fine, worked without water, replaced in washer spot, reconnected water, worked fine. Put clothes in, wouldn't agitate, smelt burning again.

Pulled washer away from wall. Observed problem. Ordered belt. Went on vacation. Cut belt in two to remove. Removed flex coupling to pump. Tried to force new belt onto big sheave, but couldn't really access properly. With help, tipped washer onto its front. Then access permitted forcing new belt onto big sheave by turning (only one direction permitted by gear box). Most of time spent cleaning up oil from gearbox which dripped on floor and splattered on back wall. Wonder how long 15 yr old gearbox will last?

I had to tilt the machine to gain access to the screw that holds the yoke bracket in place. Then I removed the one screw that holds the yoke bracket and removed the yoke and it's cushion. I then had to remove the two friction pads from the old yoke and install them on the new yoke. I was able to re-use the old yoke cushion and after re-assembling the yoke and cushion, I installed this assembly with the one screw. Righted the machine and the job was done.