Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWA3650SALHA

WWA3650SALHA General Electric Washer - Overview

Get Parts and Repair Help for WWA3650SALHA

If you know the washer repair part you need, you can browse the list of all parts on the WWA3650SALHA, or you can search by name or part description. You can also find your part by where it is located on the WWA3650SALHA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WWA3650SALHA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.52

Timer Knob Clip

The timer knob clip on your washing machine connects the timer knob to the control panel. If your timer knob is damaged or will not stay in place, you may need to replace the clip....

$7.32

V-Style Drive Belt

This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise. If you have a top-load washer, a drive belt may be connecting the transmission to the drive motor. It would generally be a rubber V-belt covered in fabric to allow free movement. Or it could be a rubber belt aided by a tensioning device like an idler pulley, to stop the motor from causing too much friction to the belt. For front-loaders, the drive belt goes between the drive motor and the wash basket. If your drive belt is worn or frayed, it should be replaced straight away. After replacing the drive belt, run a wash cycle to ensure the belt is correctly fitted.

$16.33

Timer Knob with Clip

$10.69

Compression Ring

This compression ring works in conjunction with the timer dial.

$2.06

Screw

This screw is sold individually.

$5.13

SCREW-PKG 12

$7.63

Hose Clamp Kit

This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of t...

$4.13

Drain Hose Tie Strap

$25.62

Lower Shaft Seal

This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.

$10.35

Levelling Leg

This levelling leg is less than three inches long.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

GE washer no spinning during spin cycle

  • Customer: Laurence from Bronx, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 144 of 159 people found this instruction helpful
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Lo... read more

washer was not agitating or spinning

  • Customer: Rachelle from Kent City, MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 52 of 56 people found this instruction helpful
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off and putting the new b... read more

lost all gear oil bottom of transmission

  • Customer: opal from richmond, KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 22 of 25 people found this instruction helpful
put washer on its side,removed 1cross section,loosened the nut that held on the pulley.
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose,set washer to spinan... read more