WW2780B-C Jenn-Air Wall Oven - Instructions

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

I removed the bad element - two screws, and tested it on my meter as recommended. The test meter showed it was bad, so I ordered a replacement element from PartSelect. I did check getting a part from a local dealer, and it would have been $10 more. The help and recommendations I recieved on the PartSelect repair forum make it easy.

Terry Hausler

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

My wife removed old element and replaced new element by removing and rescrewing 2 screws and detaching and retaching 2 wires to thr respective elements in about 5-10 minutes.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

The heating element is held in place by two phillips screws which were rusted fairly tight, visible at the back of the oven. I tapped my screwdriver with a hammer as I loosened them. (I would have used liquid wrench if the hammer did not work) Two wires are fastened to the element by two clips that you can slide off by hand. Slip the wires off the old element and onto the new element and install the two screws and you are done.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

I opened the oven door and unscrewed the two screws that connected the element to the back of the oven. I then pulled the element forward but it would not expose the electrical connections that powered it. I pulled a little harder and it would not pull through the insulation. I then decided that it must be accessable from the back. I took off the door the lighten the oven. I pulled the oven out of the cabinet till the conduit was taught and I could just barely see that there wasn't a panel to access the connection. I then put the back into the cabinet and pulled a little harder yet on the element and the connecters pull through the insulation. I was then able to test the element with the multimeter and decide the power was getting to the element but no heat. I ordered the part the next day. Recieved it the day after that, smokin' fast service I must add. Installed the element and it works like a new one. My wife loved it and then she loved me.

I removed one screw easily. The other screw was difficult to remove without stripping it. I sprayed wd 40 and let it sit overnight. The next day, my husband sprayed it again and after trying several different size phillips screwdrivers, he got the second screw out. He easily removed the element and then the two wires from it. He attached the two wires and replaced the screws. We tested it and it worked. The best part is: my husband scrubbed the oven before putting all the parts back!

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

I pulled off the facia from the microwave/oven. Unscrewed the plate holding the microwave and slid out the microwave. The microwave and oven are a unit. I unscrewed the oven from the hole it sits in and slid out the oven and set it on a sturdy chair. Then I unscrewed (6 screws) the bracket that holds the microwave to the oven. After that I unscrewed (14 screws) the top sheetmetal plate on the oven and slid that around behind the oven. Then I unscrewed the grounding strap inside. Did the 2 screws on each side of the oven holding the fan unit and slid that out. Undid the 2 wires plugged into the motor and the 2 screws holding the fan motor. Then I slid off the fan from the old motor and slid it onto the new motor and reversed the whole process.

Removed old element, 2 screws, cleaned oven , 60 minutes, replaced with new element, working like new, wife thoroughly impressed...