WVSR1060DBWW General Electric Washer - Instructions

Removed the four torx-head screws on the top of the washer. Pulled the control panel forward. Removed the four screws on the back of the washer and the two screws that held the dual valve on. These six screws required a nut driver. Pulled the small hose off the old valve. Then reversed the procedure. Total time to replace the faulty old part was about ten minutes. With saftey in mind, disconnect the electrical cord and shut the water valves off at the wall.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.

The agitator is the tough thing to remove, I took a previous posters advice and used a rope and 2 boards to pull it up. I will describe it as many short ropes but it can be done without cutting the rope if you think a lot about it. loop the a rope under the agitator so its under 1/2, loop another rope under the other side. tie both loops so you can slide a board in each across the top of the washer. Then tie the 2 loops together on 2 sides down near the bottom of the agitator otherwise they will come out from under it when you pull. then slide the boards in the loops and lift up pulling up the agitator.That is the hard part. Remove the bolt on the coupling, and pull it off. The new one had to be lightly hammered on with a rubber mallet, then use the new bolt. the Agitator slide down and with a push down it popped on. Putting the new part on only took 15 min, removing the broken one took about 45 min. Washer is woking great now ! Saved over $100 or buying a new washer !

pulled old knob out as far as I could, inserted small screwdriver underthe knob to push out the plastic pin. Placed new pin halfway on new knob and pushed onto shaft. took screwdriver and pushed pin in the rest of the way.

I used the video instructions sent to my email and everything worked perfectly as instructed.

The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.

I used needle-nose pliers to pry out the little c-clamp that held on the timer knob, then easily pulled off the knob. I used the vacuum cleaner to clear the broken plastic teeth from area surrounding the stem. Then I simply pushed on the new knob. Whole job took about 5 minutes.

Removed front panel assembly, removed knob's and unplueg harness,removed timer ass. screws. and installed new one in reverse order.

recieved part in 3 days put knob in and was ready to go, good as new thanks

Unplug washer, turn off water and remove the supply hose, remove 5 torex screws remove panel disconnect two wire plugs remove 2 philips screws squeeze hose clamp remove old valve install new valve reversing directions

Unplugged power cord and shut off water supply. Then removed both water hoses from the dual water inlet value using adjustable pliers. Next removed four (4) star screws on top of the control panel. This required the purchase of a #20 torq screwdriver from sears costing $3. 99 Plus tax etc. Once the top panel lifted upward and to the left I was able to unplug both electricle connections on the water inlet vlaue. Next unscrewed two phillips head screws holding the water inlet value in place. Installed the new water inlet value in reverse of above. Time to complete was 22 minutes. Very easy repair to accomplish.

We were lucky, the agitator came off on its own. Removed the coupler which cracked when a sheet got stuck underneath it! Replaced coupler and new screw/nut combo, popped on agitator. That easy.

Took the knob and clip off the dryer and stuck the knew knob on!

replaced timer module & selector button