Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WU5750Y3

WU5750Y3 Roper Dishwasher - Overview

Get Parts and Repair Help for WU5750Y3

If you know the dishwasher repair part you need, you can browse the list of all parts on the WU5750Y3, or you can search by name or part description. You can also find your part by where it is located on the WU5750Y3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for WU5750Y3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for WU5750Y3

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$46.06

Door Gasket - Gray

This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cyc...

Order within the next 6 hrs and your part ships today!
$2.96

Spring, Lid

The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not opening properly, replacing the dispenser spring could be the solution. For this replacement you will need needle nose pliers. First, release the cover on the detergent dispenser, then remove the cover from the shaft it hinges on. Pull the shaft from one side and remove the spring from the shaft. Next, replace with the new spring and engage the two open hooks into the soap cover. Finally, grasp the hook and pull it over tab on the side of the wash cup. Verify that it works properly by opening and closing the cap. Refer to the manual provided by the manufacturer for further instructions.

Order within the next 6 hrs and your part ships today!
$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

Order within the next 6 hrs and your part ships today!
$4.12

Torx Screw

7-18 x 3/4" - sold individually.

Order within the next 6 hrs and your part ships today!
$4.37

Soap Cup Latch Kit

This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are n...

Order within the next 6 hrs and your part ships today!
$24.25

Door Latch Bolt

This is a door latch bolt for a dishwasher. The door latch bolt fits on the top of the dishwasher door to keep the door closed while the appliance is running. The latch also prevents the dishwasher from running when the door is not closed, so your dishwasher may not run if the door latch bolt has been compromised. This part does not include the latch lever, so consider ordering that part as well if necessary. It is made entirely of plastic, is black in colour, and is approximately 3.5 inches wide. To access the latch bolt, you will need to remove the inner door panel of your dishwasher.

Order within the next 6 hrs and your part ships today!
$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

Order within the next 6 hrs and your part ships today!
$17.51

Upper Dishrack Roller Assembly

This part is gray in color and measures approximately 1-1/2 inches wide by 2-1/2 inches high by 1 inch deep. The dishrack roller assembly allows you to roll the rack with ease while the rail supports it. If you notice that the rack is not sliding back and forth easily or the dishwasher is not shutting properly, it may be due to the roller assembly needing to be replaced. The roller assembly may also break or go missing, and will need to be replaced for these reasons, too. You will need to remove the end cap of the upper rack to remove the entire rack. Use a flat-head screwdriver to snap the old roller assembly out of place. The new rollers just get pushed onto the shaft. Use the clips to lock into place. It is common for these rollers to wear down at the same speed, so you may want to replace all the rollers on the rack at the same time.

Order within the next 6 hrs and your part ships today!
$6.43

Cap, Wet Agent Assembly

This cap does not require the use of an O-ring seal. The wet agent assembly cap is clear in color and made of plastic. This is a part for your dishwasher. This part may need to be ...

Order within the next 6 hrs and your part ships today!
$4.88

Screw

Sold individually.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher leaking at bottom of door

  • Customer: Eileen from Salt Lake City, UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 172 of 177 people found this instruction helpful
Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked.
Verified that manifold bearing was not work. It was OK.
Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged wit... read more

leaking water

  • Customer: mary from Fountain Green, UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 61 of 72 people found this instruction helpful
The first thing I did was to investigate. I needed to find where the leak was coming from. It was leaking from just above tne door front panel, directly underneath the control panel buttons. I opened the dishwasher door, and decided to remove the door screen vent. I was covered with some offwhite fiberous, or filter like material. I thought perhaps the filt... read more

Water was dripping out of the front of the unit down low.

  • Customer: Phil from atascadero, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 54 of 58 people found this instruction helpful
I removed the old gasket, installed the new one which took about 20 seconds.Tested the unit, water was still dripping, but in a different fashion.As per a previous poster's instructions I removed the vent cover. (Located inside the dishwasher up high.)I cleaned out the calcium deposits with hot water and a sacraficial toothbrush. "Ta-Da!" Everything is now g... read more