Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WU4406V3

WU4406V3 Roper Dishwasher - Overview

Get Parts and Repair Help for WU4406V3

If you know the dishwasher repair part you need, you can browse the list of all parts on the WU4406V3, or you can search by name or part description. You can also find your part by where it is located on the WU4406V3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for WU4406V3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

$3.02

Spring, Lid

The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not opening properly, replacing the dispenser spring could be the solution. For this replacement you will need needle nose pliers. First, release the cover on the detergent dispenser, then remove the cover from the shaft it hinges on. Pull the shaft from one side and remove the spring from the shaft. Next, replace with the new spring and engage the two open hooks into the soap cover. Finally, grasp the hook and pull it over tab on the side of the wash cup. Verify that it works properly by opening and closing the cap. Refer to the manual provided by the manufacturer for further instructions.

$3.02

Cover Screw

Sold individually.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

$3.02

Screw - 8-18 x 5/8

Sold individually.

$3.02

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$6.36

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$3.02

Screw - 8-18 x 1/2

Sold Individually.

$29.47

Drain Check Valve with O-Ring

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$25.28

Detergent Dispenser Cover Kit

This kit also includes the lid hinge pin, spring, snap and latch.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher Not Draining

  • Customer: Lewis from Portsmouth, NH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 151 of 195 people found this instruction helpful
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; used pliers to remove ... read more

Lower Dishwasher rack replacement

  • Customer: Claire from Saratoga springs, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 42 of 59 people found this instruction helpful
I ordered the part and was hoping to just take out one rack and put in the other, there were NO instructions or even a diagram of the rack. There was a fold down rack that was not attached and a few parts that I have no idea what they are. This was very discouraging. The main thing is that the rack is quite a bit lighter than the original one so I doubt i... read more

Tines were broken and rack was damaged

  • Customer: Dennis from Littleton, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 40 of 69 people found this instruction helpful
Replaced the dish rack.

Removed the retaining clips on the front of the rail and removed the old rack.

Removed the spray arm assembly from the old rack.

Assembled the new rack, with the supplied parts from the kit. Using the old rack to know where some parts needed to be placed.

Put the spray arm assembly on the... read more