Models > WU3000Y0 > Instructions

WU3000Y0 Roper Dishwasher - Instructions

All installation instructions for WU3000Y0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WU3000Y0
76-90 of 153
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaking Dishwasher

  • Customer: Althea from Vancouver WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Broken roller assembly on upper dishrack.

  • Customer: michael from terrace TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Broken roller assembly on upper dishrack making the rack unuseable - to the point of us looking to replace dishwashing. But before scrapping our unit and spending $600+ -- I wanted to try to see if I could find this $13 roller. After looking at 20 something sights -- I found PartSelect -- and low and beholed -- they had what I needed!

I want to thank PartSelect for saving us $600+ -- I will spread the word to my buddies. Thanks Again !!!

front leak

  • Customer: Rod from Dripping Springs TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
pulled out the old gasket, aligned and pressed in the new gasket

The door leaked during wash cycle

  • Customer: John from Frankfort IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

Water Seeping From Under/Around The Door

  • Customer: Nate from Fort Worth TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I opened the door and pulled the gasket from around the dishwasher. The gasket does not have any adhesive around it, so it pulled free almost immediately. The new gasket was pressed into place around the door and I was done. It couldn't have been any easier. I suspected it was the gasket when I saw pinched portions that did not return to the original shape and there were no visible cracks in the machine.

leaking

  • Customer: Roy from matteson IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
put new seal in and it still leaked!hum

water leaked through door gasket.

  • Customer: Charles F. from Burnet TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Lowered door and put a weight on it to keep it open. with screwdriver pried out the old gasket. It was simple. looked at the end of the replacement gasket and inserted it into the track with the small hole down. Job Complete. about three minutes total time.

water leaking from door

  • Customer: tim from loganville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

LIght switch on oven door was broken

  • Customer: James from Sequim WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

Water leaking from front door of dishwasher

  • Customer: Gregory from North Port FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!

Upper dishrack broke

  • Customer: Veronica from Miami FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Order was very easy, received on time. Repari was sucessful.Thank you!

leak in dishwasher

  • Customer: Carolyn from Keithville LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 2 people found this instruction helpful
This was an easy fix. My husband took out the old gasket and put the new one in. It fit perfectly and no more leak. The part got to us really quickly too and that was nice. No more hand washing the dishes! :)

pump seal and impeller

  • Customer: David from Lisbon IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 2 people found this instruction helpful
had to replace the insides of a leaky pump

Dishes would'nt come clean or dry from torn boot

  • Customer: David from Sallisaw OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 8 people found this instruction helpful
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

seals were leaking,dry rotted from setting five years without using.

  • Customer: mike from seymour IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 5 people found this instruction helpful
I Disconected The 3' hose Behind Impellor.Unscrew Cap Holding Impellor In. Pull It Out, Replce With New One.Put It Back Together In Reverse
All Instructions for the WU3000Y0
76-90 of 153