Models > WU3000Y0 > Instructions

WU3000Y0 Roper Dishwasher - Instructions

All installation instructions for WU3000Y0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WU3000Y0
136-150 of 153
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Top dish rack detached from roller

  • Customer: Robert from DeSoto TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the rack end stop by pressing the clip together using hand; removed the broken roller and rack support clip by snapping away from the rack. It was literally a snap to remove and replace. Very easy to do, my 12 year son could easily replace the roller assembly.

Leaking during cycle

  • Customer: Randy from Soldotna AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

Soap dispenser not opening

  • Customer: Leslie from Brooksville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.

QUICK AND EASY

  • Customer: STEVE from WHITE PINE TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
OPEN BOX, REMOVE REPLACEMENT PART, 5 MINUTES LATER ITS DONE. MOST OF THAT 5 MINUTES WAS CLEANING ON THE DISHWASHER. THANKS.

Not draining completely

  • Customer: Sallie from Ahwahnee CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this girl did it. But, this girl also does small engine repair!

Heating element would not heat

  • Customer: Jim from Republic MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Water leaking from door

  • Customer: Kenneth from East Providence RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just followed the online instructions. I used white vinegar to clean any residue first. So easy.

water leaking from bottom of door

  • Customer: Mary Ann from Menahga MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

The part had broken, causing the upper rack to droop.

  • Customer: Jan from Bend OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair was so easy it was ridiculous...simply removed the end cap on the front of the roller assembly, took old one out, added new one and then put the end cap back on! Done in about 2 minutes!

detergent door was not opening during wash

  • Customer: Greta from Benbrook TX
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

Leaking where motor drive shaft enters pump

  • Customer: Steven from Woodstock IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

spring on dispenser broken

  • Customer: Delano from Durham NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

Dish washer not draining

  • Customer: danny from pinehurst TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked up my problem on your site and it took me to the parts most common for that problem. Your site listed the exact parts needed for my model. Got the parts and followed the direction on posted on your site by Andy.The parts were right on when I got it apart the impeller was locked up. Changed the parts without a any additional problem also took the check valve off of the underside front where the drain hose connects and cleaned it. The check valve had string and a tooth pick stuck in it. After all that hook water back up ,turned power back on and it works like a charm. Great site, parts are reasonably priced. Thank you Danny

On older model Kenmore dishwashers the water valve can fail to provide enough water to thoroughly wash the dishes.

  • Customer: James from Everett WA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Safety First: 1) I shut power off to dishwasher, 2) Shut water off to dishwasher, 3) Checked electrical with tic tracer to confirm power was off after removing bottom dishwasher panel, 4) I checked the orientation of old valve: connection plate, water inlet tubing, hose connection, and electrical connection. Then I removed the 2-screws that held the valve in place with a nut driver. Next I removed the compression clamp from the rubber hose with pliers and a screw driver. Then I removed the compression fitting and copper tubing from the old valve. Note: Kenmore used a compression fitting to connect the copper tubing to the original water valve. That said, I had to remove the old fitting and install a new one (using a pipe cutter on the copper tubing before installing a new compression fitting). I also bought a new valve elbow because the old one was not serviceable. With all three connections made up (the rubber tubing connected to the new valve along with the electrical connection, and the new elbow and compression fitting installed) I tested for leaks and reconnected the holding bracket to the side of the dishwasher frame. Before calling it good I vacuumed out the area under the dishwasher. Note: because the water inlet valve is located close to the floor, all the work had to be done while laying on the floor...awkward. This too, I had to purchase a new valve elbow and compression fitting so halfway through the project I had to make a run to the hardware store. Overall, replacing the water inlet valve on a 10 year old Kenmore dishwasher is an easy project...pretty straight forward but having to go to the hardware store stretched the installation time out to over an hour.

Roller came apart or broke apart

  • Customer: Kenneth from Mt. Carmel TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Take the stop off the end of the roller assembly, remove the old roller and replace with the new roller. Replace the stop assembly. Your done.
All Instructions for the WU3000Y0
136-150 of 153