Models > WU3000V2 > Instructions

WU3000V2 Roper Dishwasher - Instructions

All installation instructions for WU3000V2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WU3000V2
1-15 of 76
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher Not Draining

  • Customer: Lewis from Portsmouth NH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 82 of 116 people found this instruction helpful
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; used pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.

Tines were broken and rack was damaged

  • Customer: Dennis from Littleton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 32 of 56 people found this instruction helpful
Replaced the dish rack.

Removed the retaining clips on the front of the rail and removed the old rack.

Removed the spray arm assembly from the old rack.

Assembled the new rack, with the supplied parts from the kit. Using the old rack to know where some parts needed to be placed.

Put the spray arm assembly on the new rack.

Inserted the new rack into the rails

Replaced retaining clips.

Leaky water inlet valve

  • Customer: Jack from Fort Worth TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 17 of 20 people found this instruction helpful
Easy. Removed screws at top holding dishwasher to counter. Turned off water to dishwasher. Unhooked water supply line. Electrical and waste lines were long enough to leave connected and pull dishwasher out, set on side. Pull off electrical connector. Use pliars to compress spring holding water line to dishwasher, remove that line from valve. Use nut driver to remove old one, and replace with new one. Teflon tape on water connection to sink. Do everything in reverse.
done.

Lower Dishwasher rack replacement

  • Customer: Claire from Saratoga springs NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 29 people found this instruction helpful
I ordered the part and was hoping to just take out one rack and put in the other, there were NO instructions or even a diagram of the rack. There was a fold down rack that was not attached and a few parts that I have no idea what they are. This was very discouraging. The main thing is that the rack is quite a bit lighter than the original one so I doubt it will last very long. The price was more than I wanted to pay but I didn't have any options in replacement parts.

The dispenser door would not open due to a broken spring

  • Customer: LARA from Murfreesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 23 of 42 people found this instruction helpful
Removed the existing dispenser door, took off old spring. Slid new springs on pin, got it situated between the correct parts of the door. Popped it back on the pin inserts. Twisted spring into springing action position, voila. It was repaired. No repairmen. No additional costs, fees, nor extra time waiting on repairmen.

rollers and clips on botton dishrack were broken

  • Customer: Diane from Waltham MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 18 of 29 people found this instruction helpful
I pulled off the old clips and easily replaced them with the new clips and popped on the wheels.
I replaced 8 clips and 8 wheels in less than 15mins

One of the 4 latches that holds the spray arm to the top rack broke and fell off.

  • Customer: Mickey from Novato CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 19 people found this instruction helpful
It just snaps back in but it was a very tight fit and took two people to force it in. Plus I had no instructions and hadn't seen it before it broke so it took a little time to figure out where it was supposed to go. The arm doesn't connected to anything except the rack. I guess water just shoots up into it from below.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

One of the door springs broke. These add a coutner balance to the door so it is easier to open and close

  • Customer: Ruthann from Auburn WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 8 people found this instruction helpful
I have a Kenmore model that can either be totally installed under counter, left on casters or in my case installed permanently with the 'portable' covers still on. A model that is only for installation in a cabinet may be different.
Open door part way and flex the plastic hinge 'pins' on the kick plate out of the door itself. Once these are out you can close the door and lay the kick plate down towards you. This will expose a spring that is attached to pins on either side of the kick plate and held in place by a rubber cap. Remove the cap, pull the loop of the spring off the pin, and repeat for the other side. At this point you can remove the kick plate and set aside out of the way.
There is a second plate behind the kick plate held in place by four screws. Remove the screws with a Phillips head screw driver or a 1/4 inch wrench or socket, then remove the plate and set aside.
Now you have exposed the frame rails that somewhat hide the springs, one on each side. If you are lucky, like I was, only one is broken so you can use the other as a guide. Also the installation drawings that came with the part were very helpful. The information supplied by Kenmore in the parts list was no help at all.
Follow the 'assembly' found in the kit to assemble the 3 parts of the spring. A this time you may want to open the door halfway then close it and reopen a couple of times and observe how the tail of the door hinge moves, this will show you where the spring is attached. The spring is mostly hidden behind the frame rails but the two connection points are visible with the help of a flashlight. If one of the springs in still connected, observe the two connection points, one on the tail of the door hinge (top of spring) and the other in a series of slots in the frame rail.
With the door closed, hold the spring assembly in one hand (easier said than done) and hook the top of the assembly over the hook on the door hinge. Let it hang down in place and slip the lower part of the assembly into one of the slots. Again if one of the springs is still in place just use the same location as before. If both springs are missing, use one of th slots in the middle.
Only one of my springs were broken but I installed new ones on both sides as cheap insurance against doing this again in a few months.
Step by step appears a bit complicated but the whole thing only took about 10 minutes.
Good luck.

Broken Door Spring

  • Customer: Don from Christiansburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 11 people found this instruction helpful
I removed the lower panel and looked at the directions supplied with the spring. attached the new spring. replaced the panel which only involved four screws. about a thirty min. job.

Dishwasher door would hang open with no tension

  • Customer: Eva from Northport NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
My dishwasher is an under the counter mounted model. No need to pull it out or move it. I used a screwdriver to remove the casing on the bottom of dishwasher. I then removed another piece that was just behind this casing. When this was done I could see where the springs were on either side of machine right in the front, - easy access. I followed the directions that came with the part. Three simple pieces came in clear bag. You first put plastic red end onto end of long metal piece and put it through the spring. Hook it into place by catching one end of spring. I took notice of how broken springs were hanging in machine and then replaced the new spring. I hung one end of spring on the hook and then pushed other end with red plastic piece through to catch the notch. (You can adjust placement for door tension considering there are at least three notches.) Space was tight so I held onto free end of spring with needle nose pliers and pushed it through with my fingers to the notch. I almost called a repairman to do this for me. That would have been an expensive way out of an extremely easy repair. ANYONE can do this as long as they have finger dexterity. I am thrilled to have a perfectly functioning dishwasher door again. The parts were perfect and much cheaper than buying from Sears or elsewhere.

bottom rack was starting to rust away and we needed a new one

  • Customer: pat from muncy PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 12 people found this instruction helpful
The dishrack came in one box I opened the box snapped on the rollers and the bumpers and put it in the dishwasher, could not have been easier Thank you partselect

Upper Spray Arm broken off

  • Customer: Julia from Colorado Springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
It was so easy , I first put one side of the clamp on the little rack area in the center of the upper rack then pushed the other side on. It took less than five minutes. No tools needed. Julia

Coating on the rack has worn exposing the metal underneath

  • Customer: Susan from Shelby Township MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 7 of 12 people found this instruction helpful
There were no instructions with the part, but looking at the old rack it was simple to see how the parts should be assembled. Took the center part from the old rack, twisted off, and applied it to the center of the new rack. Snapped on the wheels and was done. Very simple assembly.

The bottom dishrack was having areas that were breaking off and showing rust.

  • Customer: Ed from Schofield WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 10 people found this instruction helpful
We took the rollers off the old one (new ones came with the dishrack also) and put them on the dishrack (they snapped on). There was also an extra piece that we figured out how to put on. Then slid it in place and it was fine.
All Instructions for the WU3000V2
1-15 of 76