WU3000V1 Roper Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Three rollers fell off
I removed the old rollers. This took a while to figure out how to get the old rollers off. Also it was difficult due to the fact that they had been on the basket for a long time. As soon as I figured out how to take them off and put the new ones on, it was fairly easy. The instructions were non -existent which is why it took a while.
Parts Used:
-
Susan from Oakland, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rear rollers on bottom rack broke off
real easy to install. i took off all 4 sets of rollers. i installed the first set improperly and the 2nd,3rd and 4th properly. i then went back and refasten the first one. no tools needed. 15 min.
Parts Used:
-
MARK from W.BARNSTABLE, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Part
I just installed the new part. There were no tools required. I bought an extra part
I ordered the part on Monday, and it arrivefor the other side in case it breaks.
d by FedEx the next day. I live in Southern California.
Great service, thanks.
I ordered the part on Monday, and it arrivefor the other side in case it breaks.
d by FedEx the next day. I live in Southern California.
Great service, thanks.
Parts Used:
-
Gary from Palm Springs, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wheels broke on lower tray
pulled old wheel housing off and replaced with new replacements ones. Straightforward task.
Parts Used:
-
RICHARD from JERSEY SHORE, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Installed wheel assemblies to rack
-
Philip from Greene, ME
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Parts Used:
-
Phillip D from Auburn, AL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
8 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
6 wheels missing
easy - removed old wheel holders & pushed new
ones in place. parts came in two days !!!!
ones in place. parts came in two days !!!!
Parts Used:
-
Tom from Wappingers Falls, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Parts Used:
-
Michael from Las Vegas, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Parts Used:
-
Nicole from Newnan, GA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Parts Used:
-
craig from Columbia, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
4 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers had broken on old rack
Received new rollers promptly as ordered. Removed the old ones by snapping them off and simply snapped the new ones on. Took less than 5 minutes and job was a complete success. Wife happy and I am safe for now
Parts Used:
-
joel from jena, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Soap cup latch was broken and dispenser cover was worn.
Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.
Parts Used:
-
Thomas from Columbia, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lower rack wheels
took off the old wheels and put on the new.couldn't be easier.
Parts Used:
-
john from mastic, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
missing part
-
Ruby from Saint Marys, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gasket around nozzle cap wouldn't stay on - in two pcs.
As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.
Parts Used:
-
Donald from Albuquerque, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!