Models > WU3000V1 > Instructions

WU3000V1 Roper Dishwasher - Instructions

All installation instructions for WU3000V1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WU3000V1
61-75 of 102
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

We needed a new bottom dishrack the old one was very rusty

  • Customer: Katherine from Coos Bay OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.

3 of 8 wheels had broken off bottom rack.

  • Customer: Mederick from Gorham ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Piece of cake. Unsnapped the old parts, studied the new ones for a minute to orient myself, and snapped them on. Not quite as simple a twist as the old ones took, but no problem once they were lined up properly. Total time, about 5 minutes or less.

wheels broke on lower tray

  • Customer: RICHARD from JERSEY SHORE PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
pulled old wheel housing off and replaced with new replacements ones. Straightforward task.

rear rollers on bottom rack broke off

  • Customer: MARK from W.BARNSTABLE MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
real easy to install. i took off all 4 sets of rollers. i installed the first set improperly and the 2nd,3rd and 4th properly. i then went back and refasten the first one. no tools needed. 15 min.

end loop on each end of spring broke off

  • Customer: Eieen from Methuen MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Looked at right side of dishwasher to see how it was attached and did the same. Spring was slightly shorter than the original and the loops are not a sturdy. Will see how long it last.

melted waste water guard

  • Customer: Gary from Erving MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
removed what was left of old guard and replaced it with new.

LIght switch on oven door was broken

  • Customer: James from Sequim WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

Dishes would'nt come clean or dry from torn boot

  • Customer: David from Sallisaw OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 8 people found this instruction helpful
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Latch had broken on detergent dispenser cover

  • Customer: Phillip D from Auburn AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 20 people found this instruction helpful
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.

Drain hose cracked. Leaked and warped wood floor.

  • Customer: James from Jupiter FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 2 people found this instruction helpful
Checked fill line. No leak. Checked drain hose, found crack in hose. Ordered the part, replaced.

Removed hose clamps on drain to DM and garbage disposal. Replaced hose and tightened clamps. Checked for leaks. Buttoned up faceplate on bottom of DM.

Dishwasher had no water coming into the bottom of it

  • Customer: Kathy from Kennedy AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 10 of 33 people found this instruction helpful
Took the old one off and replaced it with the new one we received from you. It was great because we received the part just in time to do the Thanksgiving dishes! Thanks PartSelect.

Door hinge broke

  • Customer: David from Vancouver WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 12 people found this instruction helpful
All pieces just snap off and the new one just snap right back in place.

Remeber take a little time to do your repair correctly.

It is cheaper to repair an appliance than it is to replace.

Replacement need for dish rack on our kitcheaid dishwasher

  • Customer: Beverly from East Troy WI
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 2 of 10 people found this instruction helpful
Unable to solve problem as the rack did not fit even though it was for a kitchen aid dishwasher. Returned it as it did not fit our model

The previous rod holding the cup in place broke

  • Customer: Nicole from Newnan GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 8 people found this instruction helpful
Remove completely the old one and installed the new entire kit.

just wanted to replace the upper dish rack - the pieces have been rusting through

  • Customer: George from Monterey CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 8 people found this instruction helpful
no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.
All Instructions for the WU3000V1
61-75 of 102