Models > WU3000V1 > Instructions

WU3000V1 Roper Dishwasher - Instructions

All installation instructions for WU3000V1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WU3000V1
46-60 of 102
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The rear roller frames became warped & made it hard to put the rack in.

  • Customer: Laurence from Sherman Oaks CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Simply snapped out the old ones and snapped in the new ones. Worked like a charm. Glad you had the parts.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 11 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

EXISTING SPRAY ARM BROKEN

  • Customer: MICHAEL from VALLEJO CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
SNAPPED IN NEW PART

RACK WAS RUSTING OUT

  • Customer: William from Rochester IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.

Dishrack Tines were breaking off due to age

  • Customer: Keith from Dayton TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
The rack came with pictorial instructions which were fairly veg, however they were to the point. The wheels snapped into place easily, and the center water transfer tube twisted off the old one and twisted on the new one just fine. It is a very good idea to keep the old one out to look at as a guide. There were no instructions on how to remove the transfer tube, I was lucky to have already worked on these before. After that it fits and works just peachy.

soap dish door does not always pop open

  • Customer: John from Dubuque IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 6 of 18 people found this instruction helpful
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

Broken wheels on lower rack

  • Customer: Annette from Grosse Pointe MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
This problem was making me NUTS! Every time I pulled the lower rack out, the rack would go off the track, threatening to break every dish, and I would literally have to half-carry the rack to move it in and out. VERY frustrating. No money for a new dishwasher, didn't want to pay for a whole new lower rack ($100). Then I discovered I could simply replace the wheel assemblies for less than $30 and no toold required. Yee-hah! It was literally a SNAP!

6 wheels missing

  • Customer: Tom from Wappingers Falls NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
easy - removed old wheel holders & pushed new

ones in place. parts came in two days !!!!

broken roller wheels

  • Customer: Whitney from Menlo Park CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Loading and unloading the dishwasher can be a pain if the rollers are not aligned or falling off. This part was easy to install even though it didn't exactly match the original (very old) dishwasher parts.

Upper dishrack needed replaced

  • Customer: Scott from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 2 of 7 people found this instruction helpful
I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

Three rollers fell off

  • Customer: Susan from Oakland CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I removed the old rollers. This took a while to figure out how to get the old rollers off. Also it was difficult due to the fact that they had been on the basket for a long time. As soon as I figured out how to take them off and put the new ones on, it was fairly easy. The instructions were non -existent which is why it took a while.

Installed wheel assemblies to rack

  • Customer: Philip from Greene ME
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Assemblies snap on, no tools needed

old spring broken

  • Customer: karen from Galloway NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
after figuring out how to position the door the instructions were good

wheels broke on lower tray

  • Customer: RICHARD from JERSEY SHORE PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
pulled old wheel housing off and replaced with new replacements ones. Straightforward task.

Wheels on bottom rack were broken

  • Customer: Tim from Fenton MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I layed the bottom rack upside down on the counter. Removed the old wheel sets and the new ones just snapped into position. I think the rack rolls better now than it ever did with the original equipment. I'm glad we purchase the Tandem Rack Rollers instead of a new dishwasher, it works great.
All Instructions for the WU3000V1
46-60 of 102