Models > WTW7990XG0

WTW7990XG0 Whirlpool Washer - Overview

Get Parts and Repair Help for WTW7990XG0

If you know the washer repair part you need, you can browse the list of all parts on the WTW7990XG0, or you can search by name or part description. You can also find your part by where it is located on the WTW7990XG0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WTW7990XG0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$90.09

Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

Order within the next 8 hrs and your part ships today!
$74.59

Lid Lock Assembly

This part makes sure that the lid is shut before allowing the machine to start or agitate.

Order within the next 8 hrs and your part ships today!
$2.71

Hose Clamp

$5.29

Hose Clamp

This hose clamp is sold individually.

Order within the next 8 hrs and your part ships today!
$9.62

Drain Pump Hose

Order within the next 8 hrs and your part ships today!
$29.34

SENSOR

Order within the next 8 hrs and your part ships today!
$2.71

Screw

This screw is sold individually.

$9.72

INLET HOSE

This hose can handle hot or cold water and is five feet long.

Order within the next 8 hrs and your part ships today!
$15.20

Hose, Recirc Pump

$15.94

Siphon Break Kit

This six piece washing machine syphon break kit for is intended for use with plastic drain hoses. Use this kit with your Whirlpool/Kenmore brand washing machine.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loose change entered drain pump, cracked housing leaked all water out

  • Customer: ROBERT from BARRINGTON, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 164 of 186 people found this instruction helpful
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and i... read more

Water pump for draining

  • Customer: Kerry from Alleyton, tX, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 49 of 58 people found this instruction helpful
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring clamps, unhooked the wi... read more

Original drain pump housing broke causing leak all over laundry room floor

  • Customer: tom from Vienna, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 34 of 37 people found this instruction helpful
What a mess!
Unplug the unit, disconnect the hot and cold water supply lines. Remove the drain hose from the wall and slide the unit away from the wall.
It's easier if you lay the unit on it's side, but not required.
Using the flat blade screwdriver, or a 1/4" nut driver, remove the 8 bolts that hold the back cover and lay that aside.
Lo... read more