Models > WTW6700TW0

WTW6700TW0 Whirlpool Washer - Overview

Get Parts and Repair Help for WTW6700TW0

If you know the washer repair part you need, you can browse the list of all parts on the WTW6700TW0, or you can search by name or part description. You can also find your part by where it is located on the WTW6700TW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WTW6700TW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$89.08

Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$21.58

Basket Hub Kit

$2.70

Hose Clamp

$5.54

Touch-Up Paint - White

$54.66

Suspension Rod Kit

This part helps center and support the drum, transmission and motor assembly. There are 4 rods in this kit.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$70.79

Lid Lock Assembly

Also known as Latch. As per the factory, this part uses the magnet to latch and the magnet is only available with the inner lid.

$2.70

Hose Clamp

This hose clamp is sold individually.

$94.00

Water Inlet Valve with Wire Harness

$2.70

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loose change entered drain pump, cracked housing leaked all water out

  • Customer: ROBERT from BARRINGTON IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 103 of 113 people found this instruction helpful
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and i... read more

Washer always stopped at the 47th and 24th minute of each load and display F1 error code. I would have to press "cancel" and then "start" a few times for it to continue.

  • Customer: James from Turnersville NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 86 of 100 people found this instruction helpful
Removed the dial control top covering by unscrewing the 3 screws in the back of the cover. Once the cover was off, the control module was exposed and all I had to do was:

1. Disconnect the wires that were plugged into the control module

2. Remove the old module. There was 1 screw holding it in place.

3. Replace with the new... read more

Water pump for draining

  • Customer: Kerry from Alleyton, tX TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 29 of 31 people found this instruction helpful
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring clamps, unhooked the wi... read more