Models > WTW6600SW2 > Instructions

WTW6600SW2 Whirlpool Washer - Instructions

All installation instructions for WTW6600SW2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WTW6600SW2
46-58 of 58
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noisy

  • Customer: Donald from Ormand Beach FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.

f1, code on the face plate of the washer,we kept on resetting it

  • Customer: Delinda M from Chicago IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved

noisey water discharge pump

  • Customer: MEECHE from LANCASTER SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .

Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!

  • Customer: Bonnie from Baytown TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)

replace suspension rods

  • Customer: brett from seymour IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.

washing machine showed F50 code

  • Customer: david from knoxville TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over

Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump

  • Customer: CARROLL from HENDERSONVILLE NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.

vigoirously shaking causung UL code

  • Customer: Josh from Lodi CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced rods with new set of 4

replace suspension rods

  • Customer: Rick from Hamersville OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
lifted top using putty knife to push back holding clips.secured top so it did not fall. moved basket to one corner and lifted the spring up, while it was lifted remove the plastic holding rings. Then push down on holding clips that are near bottom of side of basket and the suspension rod just eases out. do that for all 4 and you are done.

Washer not rotating F 51 Code RPS Failure exhibited

  • Customer: robert from linthicum MD
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Removed tub to ensure nothing caught to stop rotating. 2. Removed rotor and noted stator had fracture across center from coil to coil. 3. Changed stator, RPS and harness. 4. tested and received F 50 code (no rotation sensed by RPS.5. Changed RPS control board-washer works fine. Hope this repair acts as having a new washer again.

drum made loud noise

  • Customer: axel from lighthouse point FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

Drain Pump Leaks

  • Customer: Stuart from King George VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnect power and water. Remove the back panel of the washer. The drain pump is on the lower left corner (looking at the washer from the back). Access the electrical connection to the pump motor by lifting the lid where the wire enters the motor. You should be able to do this with your fingers and moderate pressure. Disconnect the electrical plug from the pump motor. Use pliers to remove the two hose clamps, one on the inlet and one on the outlet. Water may leak at this point so have some towels ready. Using a 5/16 wrench/nut driver, remove three hex head self threading bolds that connect the pump and motor to the underside of the tub. The replacement pump and motor go in in reverse order. Note that the replacement pump comes with a moisture shield. The shield installs on top of the new pump between the tub and the pump. It is difficult to see how the shield fits in place when fitting it to the replacement pump. The best way to see how the shield fits in place is to align it on the tub where the defective part was removed. Before testing the repaired washer, consider removing the inner tub and drain compartment cover (located at the bottom back of the inside of the washer). This takes some effort; however, it will save you from repeating this repair. Look for coins or other debris under the inner tub. For instructions on removing the inner tub and drain cover, go to youtube to watch or search for the model number and tub removal on your favorite search engine or youtube. Finally, use the spin and rinse cycle to test the repair. Look to see the pump drains the washer and ensure there are no leaks around any of the hose clamps. Good luck with your do it yourself home repair.

Washer making noise down close to bottom of machine.

  • Customer: Ronald from Demopolis AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.
All Instructions for the WTW6600SW2
46-58 of 58