Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WTW5700SW0

WTW5700SW0 Whirlpool Washer - Overview

Get Parts and Repair Help for WTW5700SW0

If you know the washer repair part you need, you can browse the list of all parts on the WTW5700SW0, or you can search by name or part description. You can also find your part by where it is located on the WTW5700SW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WTW5700SW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for WTW5700SW0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.80

Agitator Directional Cogs

Agitator directional cogs, otherwise known as dog ears, come in a package of four and are generally found in washers where the motor is connected directly to the washer. The agitat...

Order within the next 10 hrs and your part ships today!
$11.77

Direct Drive Motor Coupling

The direct drive motor coupling, also known as a coupling kit, is a newer version of the part and is used in your washer. The piece includes new metal sleeves that have been added in order to strengthen the part. This part works between the transmission and the motor; it is only used on direct drive washers with no belt. In order to replace this part, you will need a flat blade screw driver, a quarter inch nut driver, and a Phillips screw driver. Before making this repair remember to disconnect the power supply, and both fill hoses.

Order within the next 10 hrs and your part ships today!
$2.84

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched ou...

Order within the next 10 hrs and your part ships today!
$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpool part with two ports for water to pass through, a large one and a smaller one, that will need replacing if the washer has a defective pump. Tools needed are slip joint pliers, a flat blade screw driver, and a putty knife. Sandpaper might also be needed to remove rust from internal parts to install the new pump. The washer will have to be disconnected from power and tilted on its back.

Order within the next 10 hrs and your part ships today!
$44.29

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to ...

Order within the next 10 hrs and your part ships today!
$23.02

Switch, Lid

This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is having trouble starting, is not agitating, spinning, or is not draining properly, this could be because the lid switch has broken. You will need a 5/16-inch nut driver for this repair. The package will contain one lid switch. You will need to access the back of the washer, and remove the two Phillips screws that hold the top back panel in place. Slide the panel forward to release. Use your nut driver to loosen the screw that holds the ground wire in place. Lift the lid of the washer to release the old lid switch.

Order within the next 10 hrs and your part ships today!
$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of th...

Order within the next 10 hrs and your part ships today!
$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Order within the next 10 hrs and your part ships today!
$15.20

Agitator Cam Kit

This kit included the cam, 4 dogs and bearing.

Order within the next 10 hrs and your part ships today!
$4.37

Seal, Inner Cap

This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.

Order within the next 10 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 926 of 983 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

washer wouldn't agitate

  • Customer: mike from Kent, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 686 of 715 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

Water pump leaking when machine used.

  • Customer: Tom from Granby, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 534 of 563 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more