The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This suspension rod kit is a genuine OEM kit specially designed for washing machines. Each kit includes a set of 4 rods, 4 suspension balls and 4 bushings. The suspension rods are responsible for supp...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
$44.48
In Stock
Questions And Answers for WTW4950XW2
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Neal
February 11, 2020
Washer does not drain and spin as it should. I replaced the belt this morning, but it sounds to me like there is a problem with the timer starting the spin cycle as it should.
For model number WTW4950XW2
Hi Neal,
Thank you for your question. If the washer is not draining or spinning, the issue is likely the lid switch and you will need to test it with a multi-meter to see if it is working correctly. Set your multi-meter to Rx1, and touch the probes to the terminals. You are testing for continuity and should receive a reading of zero. If your test results do not match those above, you will need a replacement lid switch. We hope this helps. Thank you and have a great day.
Hello Deborah, thank you for getting in touch. Based on our research, your model does not come with a direct drive motor. It uses the belt and pulley system to power the drum. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Blair
December 5, 2019
What is the part number for the water control valve
For model number WTW4950XW2
Hello Blair, thank you for your question. The water control valve for this unit is Part #: PS11754670. Please enter the part number into the site for current price and availability. Good luck with your repair!
Was this helpful?
Thank you for voting!
Dennis
March 4, 2020
Do they sale transmissions for this modlel
For model number WTW4950XW2
Hello Dennis, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS12347614. We hope this helps.
Was wondering if you could tell what causes my washer to wash an stays on wash an my clothes are still soak an wet therefore I have to switch over to the drain an spin cycle or rinse an spin an I've done calibration an reset but no luck so if u would please help me out ty
For model number WTW4950XW2
Hi Lisa, thank you for reaching out. Based on the description, the issue is with the control board, part number PS3653306. The electronic control board manages the washer's functions such as filling, washing, draining and spinning. We would recommend checking the board to fix the issue. We hope this solves your problem!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
