Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WTR430ES0 > Instructions

WTR430ES0 Westinghouse Washer - Instructions

All installation instructions for WTR430ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WTR430ES0
46-60 of 279
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing machine wouldn't drain or spin. It would run through its cycle, but only agitate.

  • Customer: Jen from Lebanon, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 9 of 9 people found this instruction helpful
Use a cup to take the water out of the washer. Get at least three large towels -- you're going to have to sop up the water when you disconnect the hoses.

Take the bottom panel off (2 Phillips head screws). Drain pump is on the right side.

Remove the two screws holding the pump to the metal bottom plate. Use a small socket wrench and/or a screwdriver. I had to use a screwdriver on the right screw and a socket wrench on the left screw! Place as many towels in the cavity as you can to catch the water that's going to come out when you detach the hoses.

There is an inlet hose and an outlet hose, attached with bright green clamps. Remove those with pliers. Clean up the water that drains out. The hose in the back (inlet) has a "coin catcher" area. Clean this out.

Attach the hoses to the new pump. Screw it down. Replace the bottom panel.

No hot Water to washing machine

  • Customer: Dominick from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

Stainless tub in front loader broke 2 out of 3 spider arms

  • Customer: Ed from International Falls, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 11 of 16 people found this instruction helpful
Removed entire tub assembly, replaced bearings and seal in rear outer tub assembly, had spider arms welded by aluminum welder. alot of work ,saved 150.00 on parts by replacing bearings, savings untold hundreds by doing it myself instead of replare man.. BIG JOB. But just plug away and it goes rather smoothly.

Water wouldn't drain from washing machine and clicking sound when trying to run

  • Customer: Bruce from Alfred Station, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
Used a shop vac to suck all the water through the drain hose. Removed the bottom front panel held by two screws on bottom and two plastic pins at the top. Removed electric connector on front of pump. Removed two screws holding pump down. Used pliers to move spring clips back so hoses could be removed. Put hoses on new pump and squeezed clamps with pliers to pull them back over the hose connection. The connection on the left was a little bit of a pain due to space limitations. Screwed the new pump down and reconnected the electric plug. Put the bottom cover back on and screwed it into place.

washer would not spin out

  • Customer: Linda from Dover, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 16 people found this instruction helpful
First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.

THANKS

Front loading washing machine broken shock absorber

  • Customer: Thomas from Epping, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
The illustarated parts break down on the Part select web site was an awesome resource. It identified the exact part that was damaged by part number and comprehensive drawing. The part was ordered utilizing the drawings and on my doorstep within two working days, regular ground shipping. The securing pins were removed from the damaged shock absorber by driving them out with a screw driver (used in place of a drift punch) and a rubber mallet. The new shock absorber was placed in position and the securing pins were installed easily by hand and were securely in place when an auditable click was heard from the securing pin when fully engaged. The shock absorber kit came with an additional securing pin in case one of the original pins were damaged. The replacement part was of superior quality to the original.

Falling apart!

  • Customer: Michael from El Cajon, CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 10 of 14 people found this instruction helpful
It started out with the tub not draining. No problem, has happened before. Remove bottom panel, take boot off of extractor motor, clear out book & check impeller for obstructions. Noticed belot was off. Got new belt. Belt would not stay on, bearings shot. Bearings are pressed into rear outer tub shell. Must remove pulley to get tubs apart. Good luck! Pulley was corroded onto shaft of inner tub. Used various tools, finally ended up grabbing hammer and beating it. Screwed up threads, broke pulley, but got it apart. Re-tapped threads, ordered new pulley. Finally got everything together. Worked intermittantly. Thought it was motor going out. Ordered new motor. It was door switch. Done spending money, bypassed door sensor. Whew! We have clean clothes! Ended up costing about half the price of a new unit, but it basically IS a new unit! Plus I have a spare motor for when that finally goes out!

Tub to pump hose leaking

  • Customer: Barbara from Los Angeles, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
From the front of the washer, I removed two sheet metal screws at the bottom of the access panel. The panel pulled off with a just a little effort due to the nylon inserts installed on either side of the panel that keep it in place. The tub-to-pump hose is located on the right hand side and easy to access. The hose includes a screw clamp and two tension retainer (?) clamps that need to be removed.Make sure to save them for the new hose! I used a phillips head screwdriver for the screw clamp and a pair of channel locks to remove the tension retainer clamps. The tension retainer clamps were easy to remove but tricky to put back on. There must be another tool used for them that I'm not familiar with. With just a little patience though, it's an easy enough repair for anyone to do.

Thumping vibration on spin cycle

  • Customer: Kerry from Pasadena, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
Remove the front lower panel. Remove the 4 plastic pins mounting the shocks using 1/2 inch short socket to hold the detent down as per included instructions. All plastic pins were stuck in place so used needle nose pliers to pull or push out. Lube the pins with grease before reinstall to help them go through the new shocks. Use the included lock nuts to lock the four legs in place as low as possible. Start the washer and level each leg while running so you can tell if the vibration is going away. Tedious method but worked.

pump quit working , washer was full of water!

  • Customer: ROBIN from BLOOMINGTON, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
first took off old pump off by removing 2 screws and removed 2drain hoses under front load washer with pair of pliers then put new pump on same as removal.

Washer wouldn't spin clothes

  • Customer: Brian from Forest Ranch, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
First thought the problem was with the spin cycle, however it soon became clear it was the pump that wasn't draining the water that kept the spin cycle from doing it's thing. After hand-wringing a large load and shopvacing out the remaining water, I ordered the new pump, got it in two days, and did a quick change out and it works perfectly. During the removal of the rubber boot that connects the tub to the pump, the one thing I did discover was a yucky buildup of years of fabric softener which I couldn't break my wife from using. But, after showing, and more importantly, letting her SMELL the fungus/mildew in the sludge, I've finally broken her of the habit! Best bang for the repair buck so far.

washer door woild not lock and would not allow washer to operate

  • Customer: Kevin from Merrimack, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.

Out of balance when on final spin cycle

  • Customer: Kevin from Vancouver, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Had to replace one Spring on top of the tub and both shock absorbers. Anyone with even a limited amount of mechanical ability could handle this repair. Save yourself about $300 in repair cost and replace these items yourself. Spring and Shocks absorber kit cost less than $60 with shipping.

Just look at the diagram that comes with the parts, it's a piece of cake. The most difficult part is replacing the spring, she is stiff. You will need to take the top of the machine off, which is super easy, and remove the metal keeper on top of the frame rail. Get someone to help you as you will need to lift the tub and slip the spring over the frame rail.

The shocks are the easiest part of the repair, and should take less than five mins. to replace.

old selector knob cracked inside could not use the dryer.

  • Customer: Marilyn from Pembroke Pines, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
removed the old selector knob just pulled it out gently and lined up the new selector knob and gently pushed it into correct alignment. what a breeze.
reasonable prices. saved me $ on a service call, part, and labor. Thank you M



I just feel the postage is way too much for an item that weighs under 1 oz.

Rubber seal (boot) needed to be replaced.

  • Customer: Jon from Stevens Point, WI
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 10 of 19 people found this instruction helpful
I began by removing the seal from the exterior lip of the machine housing. I took a razor and removed any rubber and adhesive that remained on the unit.

Next, I remove the boot from the soap dispenser tube (located at about 11:00 of the opening) with a needlenose plyers. The manual recommends flattening a 3" copper pipe to fashon a tool to release the "bread tie" fastener. I can see why but patience with a needlenose sufficed.

I pulled the boot down from the tub housing (with much force) exposing the band that holds the boot in firmly. I one pull, both pieces came out. I could tell getting the new one is was going to be a chore.

I cleaned the area and after about 40 strenuous minutes of getting the new boot onto the tub, only a couple things remained. Even with help, be prepared to dedicate hours of frustration getting the band around the boot securing it to the tub. The working space is minimal and the task is virtually hopeless to slightly possible.

Once that's taken care of, you may feel like you can accomplish anything. The rest goes up in the order it came out. Make sure you slide the boot up as far up the soap dispensing unit as possible before securing the bread tie clamp.

Run the seal around, close the door and have one of you kids clean up the work area (and mop the blood, sweat and tears from the unit and the floor.
All Instructions for the WTR430ES0
46-60 of 279