Models > WTF330HS2 > Instructions

WTF330HS2 Westinghouse Washer - Instructions

All installation instructions for WTF330HS2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WTF330HS2
166-180 of 249
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Someone opebed the washer door prior to cycle completion

  • Customer: H. Edward from Sequim WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
two screws took off the old plate, replaced the door strike with saame screws

Nylon door latch broke off. Poor design. The hinges on the Affinity washer and dryer have hinges that won't keep the latches aligned, so the strike hit the body and broke off.

  • Customer: John from Fullerton CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was easy. Two screws held it on. It's set into the door, so there is no adjustment. However, I should have bought a couple of extra ones, because the design problem is still inherent, and it will break the next time somebody is in a hurry and "slams" the door, or pulls it open before the cycle is completed. The ten pound door is held by a stike less than 1/8" thick.

Machine shook - caused wooden base to "walk".

  • Customer: Robert from Newport RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed two screws at base on front and dropped cover.Recognized broken shock absorbers as problem or possible result of more critical problem.Removed broken shocks (obstinate pins:use proper open end wrench to engage pin beneath head and drive wrench handle to pull pin. Of course, at same time, push in lock on pin's point to release)and ordered part number.Installed new shocks.Plastic pins were originally "top" toward rear, but shocks could be rotated so pins would engage bushings properly with "top" toward rear or facing front (bushings have a "stop" opposite side pin is driven in).I rotated the shock "heads" and "shafts" as I saw fit for easiest installation (some pins head forward, others head back).One shock had a head location that made it difficult to push through the hole. I located a "service" hole in the back of washer almost directly opposite this head.Used wooden dowel (maybe 20 inches)through hole in back and hammer to drive pin in place.Liquid hand soap seemed okay lubricant for all pins.

tip of strike broke off

  • Customer: Doris from Hesperia CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
unscrewed (2) screws, took broken piece off and screwed new piece on with the (2) screws. Keep your old screws because part does not come with screws.

Washer wouldn't come on because lock went out

  • Customer: Celeste from Silsbee TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ok, so I went to wash clothes and my Frigidaire Affinity wouldn't come on because it said the door wasn't locked. The switch had gone out. I researched it and bought it here. When we got it, I looked up a video on Youtube that was less than 2 minutes long. My husband and I watched it and then did the repair! It took us only a few minutes and then the washer worked! We saved time and at least $150! And it was so easy to do that I probably could have done it without my husband, and I'm not the handy type.

Would not spin

  • Customer: Faith from Sealy TX
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy.

Door strike broke due to door being off center

  • Customer: patricia from portsmouth NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the 2 screws out, removed the old and screwed in the new.Piece of cake. What stod out in the process was Part selects follow up with email and video of how to replace. They are great....

Broken shock absorbers

  • Customer: John from Richmond Hill GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My shocks on the washer were broken, in part because of age, the other is broken spider drum inside the barrel. Was very easy to do the shocks. Unhook water connections and power. Move washer away from the wall. Remove the back cover from the washer. On the left side, you have to remove two screws from the electronics control box so you can gently move it out of the way. Then grab the plastic pin with some pliers and pull while depressing the locking lug on the end of the pin (Very important to depress the lock or you will have to buy new pins) Remove both pins for each shock. I used some high pressure grease on the pins when I put it all back together. Was a quick fix. Unfortunately had to take it all back apart as this was only a small part of my issue with having the stainless drum being broken inside.

Door error on front loading washing machine

  • Customer: christina p from chapel hill NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
After searching the internet, I found out that the error code flashing on my front loading washer was an easy DIY fix. I went into our local big box home improvement store who told me to go to their online store for the part I needed. I did but had zero luck. I found the part I needed here and found a great video online which walked me through the repair. The part arrived and it took less than 10-mins to be done and have a working washer again. Thanks for the great service! From a working mom in NC

Violently vibrated and drum would come off the springs

  • Customer: Shea from Long beach CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the shocks. It was easy

broken door strike

  • Customer: Wayne from Piedmont OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
unscrewed broken one and screwed the new one in place.

Washer made loud clacking noise during spin cycle.

  • Customer: William from Punta Gorda FL
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I followed the instructions enclosed with the parts and removed the front access panel. Following the instructions for removal of the shock absorber mounting pins for the mount on the left hand side of the washer (as observed from the front) was difficult. I depressed the pin using my finger and I used a small nut driver to push the pin out. The nut driver was smaller than the pin and helped push the pin completely out. Even so, this require a lot of effort and I cut my hand when it slipped (no job worth doing always requires a little bloodletting). Installation of the replacement shock absorber in this position required moderate effort but went well. After a lot of effort trying to remove the pins on the shock absorber on the right hand side of the washer it became obvious that it was impossible to do it from the front of the washer. Other objects in the washer obstructed access to the pins. So I had to remove the back panel of the washer to aid in accessing the pins. At this point I required the assistance of my wife to depress the tab on the pins while I pulled on the pins with a pair of pliers’. The bottom pin has an obstruction where the pin pulls out. Removing the pin required quite an effort and nearly broke the pin (I guess that is why a replacement pin is in the kit). We installed the pin for this bottom mount in the opposite direction than the original pin was installed. I am sure that I saved a lot of money by doing this myself, but I would not recommend others to do it themselves.

Washer would not start

  • Customer: Gerald from Brownfield TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced doorlok as every one sujested but that did not fix it I then replaced thr control panel with a new upgraded one. It is not that simple for an amature. New control came with one of the control shafts missing had difficulty getting it in position so so control would be on right function. after all that I found diagnostic instructions taped to bottom of washer

Washer wouldn't spin shut off with 6 mintes to go

  • Customer: michelle from swanzey NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I found this wonderful web site, after removing the cover and running a diagnostic to find it was either the door lock or the TCP control board. Control board unable to find any information on was scared to call the repair man as they usually cost about $500.00. I am a single mother and order the door lock and just like that I was able to repair it myself. Thanks you so much!!!

washer would not go into full speed spinning

  • Customer: Joe from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off electricity. Unscrewed top panel. Took off top panel. opened door. Unscrewed door lock. Pulled lock up. Unplugged connections. Plugged in new part, positioned, and screwed in. Replaced top panel
All Instructions for the WTF330HS2
166-180 of 249