WTF330HS1 Westinghouse Washer - Instructions

First we took the pump off and it was full so we hoped replacing it as the fan blades were broke and it didn't help. We replaced the control board and that didn't change it either. So I checked here and the door strike and door switch could be the problem so I ordered and put them on that was the problem. Thanks so much. Instructions were well printed and the job was about 5 minutes to replace. The washer works perfectly. We should have started with these parts first and it may not have cost so much.

1. Remove the spring clamp around the tub seal. 2. Pull back the tub seal in the area by the door lock switch. 3. Remove the switch assembly by removing two Phillips screws. 4. Remove connectors from switch. 5. Install connectors onto new switch. 6. Mount new switch on washer with two Phillips screws. Reinstall tub seal making sure to tuck it correctly on the washer frame. 7. Reinstall spring clamp.

Unplug. Remove front lower cover panel. The trick is getting the old pins out and the solution was the alternate method provided in the written instructions that came with the shock kit. Use a deep 13mm or 1/2" socket over the pin end to depress the locking tab. After that, it is just a matter of prying the pins out. I was able to salvage all of my existing pins and the new (different design which will hopefully hold up much better) shocks went in pretty easily. The shock kit was reasonably priced but replacement pin were incredibly overpriced, so I was motivated to salvage the ones installed.

This is the second part I have put on it and it still does not work. It is now leaking some also. So tonight I replaced it.

I used a screwdriver to screw on the new door strike. Problem solved!

Removed two screws, installed new piece.

Took the back off the machine. pulled out the old shocks and installed the new. Put the back on. Simple

First of all, disconnect the power from the machine. Then,removed the clamp fittings to remove the old hose. At the same time I replaced the coin filter (which I probably did not have to replace since it is not a filter, more of a trap) and therein lies a warning. Make sure that the filter is pushed all the way down into the bottom of the new hose. Otherwise, it can get drawn up and lodged between the rotating washer drum and drum liner (which happened to me and was a tad difficult to get out). Then just replace the hose and attach the clamps. Other than the problem with the filter (my fault), very easy and folks at PartSelect were terrific!

Followed The instructions provided by "Part Select". Having a stacked washer & Dryer I removed the dryer and the electrical and water connections and the back panel on the washer. After that disassembley was relatively easy. Unfortunately, I got over-zelaous and removed more than I had too. Once apart I found that the Spider Arm on the Inner tub was broken. Bought the parts and reassembled in reverse order using the photos I took upon disassembley. (Trusting memory is not always the best way to go) The thing that irritated me was not being able to purchase the Spider Arm separate from the Inner Tub. Apparently Kenmore wasn't satisfied with their profit margin so they found a way to jack the price up. Regardless, I saved a lot of money and the Washer is running like a top. Parts delivery was as advertised.

Easy repair, buy shipping took much longer than advertised!

I read other problems, I jumped the gun and purchased the door switch, this was easy to change, but MY machine still had the same issues, however, I found that the filter was plugged, and after I cleaned this out, this fixed my issues and the machine works fine, So I now have a door switch and striker should mine go bad, Hope this helps out

the existing pin was in backwards and to get it out was a problem because there was not enough room behind the pin to get it out.also i thiugh there was 2 pins in the kit and there was only one.

Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!

Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!

Unscrewed two phillips head screws, removed damaged part, screwed on replacement part. Presto! Washer works again. I especially appreciated receiving the part less than 48 hours after I ordered it with only regular shipping charge.