WSM2780LCW General Electric Washer Dryer Combo - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was squeeking for a while, and then eventually just quit working.
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing).
Parts Used:
-
Jesse from Battle Ground, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
load noise
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws off the bearing bracket, that's it. easy
Parts Used:
-
jeff from coldwater, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped working
What a mess. Partselect shipped the wrong part. I paid a technician to fix it, only to learn the part was wrong. I order the right part. I needed to send it back, reorder the same part, and pay for a second visit from the technician. The nice people at partselect gave me a $7 credit for costing me $200. Losers
Parts Used:
-
Shanice from RESTON, VA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer making squeeky noise.
-
NICOLAS from LYNN, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
1 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no flame
-
EMANUEL from WALL TWP, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Dryer runs but no heat
I first checked the heating element by peeking through the peek hole in the front to see if it was turning on. The heating element turned on but gas failed to flow. Next, I checked all sensors including the fuse, they were all fine. This points to the solenoid as the cause of the issue. So I replaced the solenoids and the problem solved. I did watch the YouTube video on how to check the sensors and replace faulty parts.
Parts Used:
-
Mitsuhiro from Anaheim, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lack of grease caused bearing to go out
I took the top and front off the dryer. I then took the screws out of the drum and removed the drum. I then took the old bearing out and put the new one in.
Parts Used:
-
GARY from HALEYVILLE, AL
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Spin cycle not spining sufficient water from clothes
Remove front of unit. Replace belt that drives the washer. This repair is very easy.
Parts Used:
-
Bob from Riviera Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat
The wife complained of clothes not drying. Ordered a igniter without checking for exact cause to save time. When I was able to I took the top and front panels off. Unfortunately the igniter was fine. I ruled out the limits and igniter with a VOM meter. I quickly ordered the gas valve solenoids. After a quick delivery they were replaced with a screw driver and panels replaced. Works fine.
Parts Used:
-
jeff from perrysburg, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!