Models > WSM2700LCW

WSM2700LCW General Electric Washer / Dryer Combo - Overview

Get Parts and Repair Help for WSM2700LCW

If you know the washer / dryer combo repair part you need, you can browse the list of all parts on the WSM2700LCW, or you can search by name or part description. You can also find your part by where it is located on the WSM2700LCW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer / dryer combo. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.09

Rear Bearing

Bearing Only. This part helps your appliance run as quietly as possible.

Order within the next 6 hrs and your part ships today!
$7.47

Hose Clamp Kit

This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.

Order within the next 6 hrs and your part ships today!
$60.88

V-Belt

Order within the next 6 hrs and your part ships today!
$79.45

Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

Order within the next 6 hrs and your part ships today!
$49.55

Timer Knob

This knob accepts a D-shaped shaft.

Order within the next 6 hrs and your part ships today!
$13.04

Grounding Ball

Order within the next 6 hrs and your part ships today!
$27.72

Bearing Bracket

This bracket is used on the drum bearing.

Order within the next 6 hrs and your part ships today!
$5.98

SCREW-LOCK 10-16X 50

Order within the next 6 hrs and your part ships today!
$63.21

Blower Wheel

Order within the next 6 hrs and your part ships today!
$39.93

High Limit Safety Thermostat

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. The element will kick back in when the temperature drops to 190 degrees Fahrenheit - the differential of 70 degrees.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was squeeking for a while, and then eventually just quit working.

  • Customer: Jesse from Battle Ground WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
Took the top and the front panel off (took me a while to figure this out without breaking stuff). Took off belt, pulled out drum, replaced bearing, and then I also had to replace the ball (attached to rear of drum, which slides inside the bearing). read more

load noise

  • Customer: jeff from coldwater MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 7 people found this instruction helpful
took the top off, then the front,there 2 screws that hold the front on. there's a yellow thing on the front took that off, it is held on with one screw. on the back of the dryer on the bottom is a metal plate take that off, to get to the belt take that off. then there' 3 screws in the drum, take them off ,then you can slid the drum out. then take 2 screws of... read more

Dryer making squeeky noise.

  • Customer: NICOLAS from LYNN MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 1 of 3 people found this instruction helpful
Removed the Drum and replaced the part.... read more