Models
>
WSM2480SEZWW
WSM2480SEZWW General Electric Washer Dryer Combo - Overview
Sections of the WSM2480SEZWW
[Viewing 12 of 12]Keep searches simple, eg. "belt" or "pump".
Lint Screen Cover
PartSelect #: PS11729240
Manufacturer #: WE18X25155
This part includes both the cover and the screen.
$117.90
In Stock
Lid Switch
PartSelect #: PS270219
Manufacturer #: WH12X955
Used with washer/dryer combos. This part makes sure that the lid is shut before allowing the machine to start or agitate.
$133.26
In Stock
Timer Kit
PartSelect #: PS270214
Manufacturer #: WH12X950
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
$288.95
In Stock
Suspension Kit - 3 Pack
PartSelect #: PS2354077
Manufacturer #: WH17X10017
These parts help keep the washer from vigorous shaking during its cycles.
No Longer Available
Inlet Hose - 2 pack
PartSelect #: PS2340055
Manufacturer #: WH41X10207
Includes 2 hoses that are 4 feet long, and 4 seals.
$23.79
In Stock
Questions And Answers for WSM2480SEZWW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WSM2480SEZWW
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing machine would not cycle properly
Our washing machine had gotten stuck in the agitation cycle several times....it wouldn't cycle out of either wash or rinse, and was clogged with suds. Turns out we were using the wrong detergent, one recommended only for front-loading high efficiency washers. I removed knobs and front panel, then the two screws holding the timer mechanism
... Read more
in. Although it looked nearly new, clearly it didn't work. The replacement part arrived in two days, and was easy to install.- 5 screws holding the panel, and 2 on the timer. tested the washer today, and it worked perfectly.
Read less
Parts Used:
-
Daniel from Burnt Hills, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
17 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator was shredded
The agitator broke free while the washer was spinning and it shredded the plastic. All I had to do was remove a little top cap off the agitator by prying it up with a screwdriver, then replacing the cap on the new agitator. Viola! Done. Very easy!
Parts Used:
-
Kathryn from Signal Mountain, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
12 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken lid switch (old part worked, but plastic casing broke and screws couldn't hold it in place anymore)
The removal and installation were self-explanatory once the part was in hand. Because the unit is in a laundry closet off the bathroom, space was limited and we had to be creative. Hence, my son's Handy Manny tool set, Turner to be exact, was perfect for holding the ground wire bolt in place from behind the dryer lid so that we could loos
... Read more
en the nut on the inside of the dryer lid. Of course, when I went to put the nut back on the bolt after putting the new ground wire in place, I dropped the nut in the dryer. That's when our son's Harvey the train (a Thomas the Tank engine character) came in handy. My long arms and its magnet were just the thing to get the nut out of the abyss at the bottom of the washer cabinet.
Read less
Parts Used:
-
Cami from Roswell, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
12 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!