Models > WRT8G3EW4 > Instructions

WRT8G3EW4 Westinghouse Refrigerator - Instructions

All installation instructions for WRT8G3EW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRT8G3EW4
106-120 of 320
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

coil Iceing up

  • Customer: Thomas from Stuart FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

The meat drawer slide had broken and the drawer would fall down everytime you opened it.

  • Customer: kathleen from cypress CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Pulled the drawer out, lifted the shelf out of the refrigerator, unscrewed drawer slides from shelf and rescrewed the new drawer slides and returned the shelf, drawer, and the job was finished. Thank you so very much for your speedy delivery.

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

  • Customer: Larry from Newton KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

the refrigerator door shelf retainer bar cracked due to overstocking the shelf

  • Customer: windy from chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
popped the shelves back into the interlocking socket.

Wife leaned on drawer and broke support.

  • Customer: David from Akron OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The first thing I did was to remove all the food from the shelf above the drawer. I removed the old support rail that is attached at the rear of the shelf by one phillips screw. I installed the new support and secured it. Partselect was a great place to purchase the part and they shipped the part quickly.

Deli Drawer rail cracked

  • Customer: Chris from Goshen IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
As others have noted: this is an easy repair. I spent more time clearing all of our containers of yogurt that the actually "repair."

This is a good opportunity to clean the glass shelf and so I did that after removing it. Unscrewed the back support screw, removed old rail, and installed new one. (I just used the old screw as it seemed to be in good shape).

The hanging drawer support on the left side broke and I was unable to glue it back together effectively.

  • Customer: Matthew from Murfreesboro TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I cleaned off the shelf that the drawer hangs from and removed it from the fridge. I took the philips head screw from the back of the broken support rail. Put the new one on, screwed it in and replaced the shelf and drawer.

Broke meat keeper rail

  • Customer: Jo Ann from Ruidoso NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed shelf, inverted it, removed broken part (one screw), installed new shelf rail.

Piece of cake.

No freezing or cold in either freezer or refridgerator - compressor did not run.

  • Customer: George from Sunnyvale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

frezzer iceing over and not cooling the refrigerator

  • Customer: Marcus from Pine Hill AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

The rack-door part of my refrigerator broke-again

  • Customer: Therese from Saint Charles IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 7 people found this instruction helpful
I simply popped out the old and popped in the new. I got a terrific price, compared to other companies on line and I got it delivered in two days. Thank you!

Plastic drawer support had broken

  • Customer: charles from brighton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I Removed the old broken piece and replaced it with the new drawer support, using the screwdriver it was a very simple operation.

Drawer support rail broke!

  • Customer: Gayle from Natchez MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Very, very easy problem to fix. I took the shelf that the support rails were attached to out of refrigerator. Unscrewed broke piece and screwed in new support rail and simply slid shelf back into refrigerator. Ta~Da! If I can do it, you can do it!

Both support rails had broken

  • Customer: Alan from Blairsville PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First, remove shelf unit from refrigerator and lay glass side down on a large flat surface. Observe, then pay attention to assembly. Spent more time with this, drinking coffee, and playing with puppy, than the actual repair. Only had to remove and replace two
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.

Broken & cracked bar

  • Customer: Mike from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
push it 'till it clicks.
All Instructions for the WRT8G3EW4
106-120 of 320